Difference between revisions of "NVR/Recording Setup/Alarm Recording Setup SmartPSS 2.0"

(Step by Step Instructions)
(Step by Step Instructions)
Line 64: Line 64:
 
[[file:alarmsmartpss2_06.png|600px]]
 
[[file:alarmsmartpss2_06.png|600px]]
  
10.Next you will need to set the schedule to record the alarm event. Select Storage -> Schedule.  
+
10.Next you will need to set the schedule to record the alarm event. Select Storage -> Schedule.
  
 
[[file:alarmsmartpss2_07.png|600px]]
 
[[file:alarmsmartpss2_07.png|600px]]
 +
 +
11.Select Channel Alarm recording was set for -> Select the gear icon -> Here you will see Period 1 (By default it will be set 0-24 hours. For this tutorial we are setting 1 Period -> Check mark "Alarm" -> Check mark "all" to record everyday of the week.
 +
 +
[[file:alarmsmartpss2_08.png|600px]]
 +
 +
[[file:alarmsmartpss2_09.png|600px]]
 +
 +
12.Here on the schedule you should see red for each day of the week as pictured below. Select apply and save to save settings.
 +
 +
[[file:alarmsmartpss2_010.png|600px]]

Revision as of 00:47, 14 October 2017

How to Setup Alarm Recording Using A Physical Alarm via SmartPSS 2.0

Description

How to Setup Alarm Recording Using A Physical Alarm via SmartPSS 2.0

Prerequisites

  • A NVR or IP Camera with an Alarm Out

PhysicalAlarmRecordSetup8Large.JPG

  • A low voltage physical alarm

PhysicalAlarmRecordSetup1Large.JPG

  • Dual pair 24 gauge run to the physical alarm

PhysicalAlarmRecordSetup15Large.JPG

  • Alarm block

PhysicalAlarmRecordSetup6Large.JPG

Step by Step Instructions

1. Identify which alarm out block you wish to use to connect your physical alarm. For this example we are going to use, "Alarm Out Channel 1"

PhysicalAlarmRecordSetup14.JPG

2. Connect the cable to your physical alarm.

PhysicalAlarmRecordSetup9Large.JPGPhysicalAlarmRecordSetup10Large.JPG

3. Connect the cable to the alarm block on the ports labeled, "IN1" and "Ground"

PhysicalAlarmRecordSetup11Large.JPG

4. Log into SmartPSS -> Select "Device Configuration" from the home page.

Alarmsmartpss2 0.png

Alarmsmartpss2 01.png

5.From the left hand side select device -> Expand Event -> Select Alarm I/O

Alarmsmartpss2 02.png

6.Check mark Alarm Input Enable -> Select channel.

Alarmsmartpss2 03.png

7.Select either, "Always Open" or "Always Closed"

Alarmsmartpss2 04.png

8.Next select what actions you want the system to perform, when the alarm is activated. To record the alarm event you will need to check mark "record channel".

Alarmsmartpss2 05.png

9.Select Apply and Save to save settings.

Alarmsmartpss2 06.png

10.Next you will need to set the schedule to record the alarm event. Select Storage -> Schedule.

Alarmsmartpss2 07.png

11.Select Channel Alarm recording was set for -> Select the gear icon -> Here you will see Period 1 (By default it will be set 0-24 hours. For this tutorial we are setting 1 Period -> Check mark "Alarm" -> Check mark "all" to record everyday of the week.

Alarmsmartpss2 08.png

Alarmsmartpss2 09.png

12.Here on the schedule you should see red for each day of the week as pictured below. Select apply and save to save settings.

600px