:Perimeter

Revision as of 22:37, 4 December 2019 by Marques.Phillips (talk | contribs)

Perimeter

Description

Perimeter protection: with deep learning algorithm, Dahua Perimeter Protection technology can recognize human and vehicle accurately. In restricted area (such as pedestrian area and vehicle area), the false alarms of intelligent detection based on target type (such as tripwire, intrusion) are largely reduced.

Installation Suggestions

  • The target cannot exceed 2/3 of the height and 2/3 of the width of the image
  • Draw the cross line vertical to the moving direction of detected target as much as possible

The installation site and installation type are essential to the final performance, this section introduces how to select a proper installation site and installation type

Suitable Sites

The sites need to provide a large visual field and be open and simple. There should be no frequently moving objects or drastic changes in lighting condition.

These kind of sites are suitable for cross detection at borderlines, communities, lawns, railways, and highways, access detection at underground garages, pedestrian streets, fall detection at lakes, and access detection at rooftops and private properties

Unsuitable Sites

Installation Requirements

Perimeter Protection Installation Requirements.jpg

The shorter the installation distance is, the smaller the arm width will be

The maximum arm width for humans is 12m

Fixed Lens installation distance reference table:

Lens' focal length (mm) 2.8 3.6 6.0 8.0 12 30
Installing distance (m) 6 8 13 17 26 65

Varifocal Lens installation distance reference:

  • When the install distance is 5m~22 m, it is recommended to select the lens which focal length is 2.7mm~13.5 mm.
  • When the installing distance is 13m~55m, it is recommended to select the lens which focal length is 7mm~35mm
  • Recommended installing height: h > 3m and the maximum height varies with different lens
  • Recommended installation angle: 0° ~ 45° (elevation angle)
  • Recommended lens: Low focal length and large angle of view

Models

  • DH-SD8A240WA-HNF
  • DH-SD8A840WA-HNF

Instructions

Icon for type SystemUI Old.pngSystemUI Old

Description

This guide will show how to set up the Perimeter IVS function in the SystemUI with OldGUI

Prerequisites

  • Dahua device with Perimeter IVS function

Video Instructions

Step By Step Instructions

1. From the Main Menu

Click Event

Perimeter - SystemUI Old - 1.jpg

2. Click Smart Plan

Perimeter - SystemUI Old - 2.jpg

3. Use the dropdown box to select the channel

Click the IVS icon (light bulb) to enable the function

Perimeter - SystemUI Old - 3.jpg

4. Click Apply to save

Perimeter - SystemUI Old - 4.jpg

5. Click IVS

Perimeter - SystemUI Old - 5.jpg

6. Click Add to create a new IVS rule

Perimeter - SystemUI Old - 6.jpg

7. Click the Pencil icon under Draw to create the rule

Perimeter - SystemUI Old - 7.jpg

8. The video will full screen

Use the AI recognition interface to enable and set which Effective Targets (targets that will be valid)

Click OK

Perimeter - SystemUI Old - 8.jpg

9. To draw the rule left click inside the video frame to begin drawing

Perimeter - SystemUI Old - 9.jpg

10. Right click to finish drawing

The Rule name will confirm when drawing is complete

Perimeter - SystemUI Old - 10.jpg

11. Click Apply to save all settings

Perimeter - SystemUI Old - 11.jpg

Icon for type SystemUI New.pngSystemUI New

Description

This guide will show how to set up the Perimeter IVS function in the SystemUI with NewUI

Prerequisites

  • Dahua device with Perimeter IVS function

Video Instructions

Step By Step Instructions

1. From the Main Menu

Click AI

Perimeter - SystemUI New - 1.jpg

2. Click Parameters

Perimeter - SystemUI New - 2.jpg

3. Click Smart Plan

Perimeter - SystemUI New - 3.jpg

4. Click Add to create a new Smart Plan

Perimeter - SystemUI New - 4.jpg

5. Click the IVS icon (light bulb) to enable the Smart Plan

Perimeter - SystemUI New - 5.jpg

6. Click Apply to save

Perimeter - SystemUI New - 6.jpg

7. Click IVS

Perimeter - SystemUI New - 7.jpg

8. Click Add to create a new IVS rule

Perimeter - SystemUI New - 8.jpg

9. The new Tripwire rule will appear

Click the pencil icon under draw to create the rule

Perimeter - SystemUI New - 9.jpg

10. The video will fullscreen

Left click inside the video frame to begin drawing the rule

Perimeter - SystemUI New - 10.jpg

Right click to finish drawing

The Rule Name will confirm the rule has been created

Perimeter - SystemUI New - 11.jpg

11. Use the AI recognition interface to enable and set which Effective Targets (targets that will be valid)

Click OK

Perimeter - SystemUI New - 12.jpg

13. Click the icon under Trigger to set any corresponding event triggers

Click Apply to save all settings

Perimeter - SystemUI New - 13.jpg

Icon for type WebUI Old.pngWebUI Old

Description

This guide will show how to set up the Perimeter IVS function in the WebUI with OldGUI

Prerequisites

  • Dahua device with Perimeter IVS function

Video Instructions

Step By Step Instructions

1. From the Main Menu

Click Setting

Perimeter - WebUI Old GUI - 1.jpg

2. Under Event

Click Smart Plan

Perimeter - WebUI Old GUI - 2.jpg

3. Click the IVS icon (light bulb) to enable the IVS rule

Perimeter - WebUI Old GUI - 3.jpg

4. Click Save

Perimeter - WebUI Old GUI - 4.jpg

5. Click IVS

Perimeter - WebUI Old GUI - 5.jpg

6. Click the + to create a new IVS rule

Perimeter - WebUI Old GUI - 6.jpg

7. The new IVS rule will appear in the list

Click Draw Rule to draw the IVS rule

Perimeter - WebUI Old GUI - 7.jpg

8. Left click inside the video frame to begin drawing the rule

Perimeter - WebUI Old GUI - 8.jpg

Right click to finish drawing

The Rule name will confirm when drawing is complete

Perimeter - WebUI Old GUI - 9.jpg

9. Use the Object filter interface to enable and set which Effective objects(targets that will be valid) for the IVS rule

Perimeter - WebUI Old GUI - 10.jpg

10. Click Save to save all settings

Perimeter - WebUI Old GUI - 11.jpg

Icon for type WebUI New.pngWebUI New

Description

This guide will show how to set up the Perimeter IVS function in the WebUI with NewGUI

Prerequisites

  • Dahua device with Perimeter IVS function

Video Instructions

Step By Step Instructions

1. From the Main Menu of the WebUI

Click AI

Perimeter - WebUI New - 1.jpg

2. Click Parameters

Perimeter - WebUI New - 2.jpg

3. Click Smart Plan

Perimeter - WebUI New - 3.jpg

4. Use the dropdown box to select the Channel

Click the IVS icon (light bulb) to enable the IVS rule

Perimeter - WebUI New - 4.jpg

5. Click OK to save

Perimeter - WebUI New - 5.jpg

6. Click IVS

Perimeter - WebUI New - 6.jpg

7. Click the + to create a new IVS rule

Perimeter - WebUI New - 7.jpg

8. The IVS rule will appear in the list

Click Draw Rule to begin drawing the IVS rule

Perimeter - WebUI New - 8.jpg

9. Left click inside the video frame to begin drawing the rule

Perimeter - WebUI New - 9.jpg

Right click to finish drawing

Perimeter - WebUI New - 10.jpg

10. Use the AI recognition interface to enable and set which Effective objects(targets that will be valid) for the IVS rule

Perimeter - WebUI New - 11.jpg

11. Click OK to save all settings

Perimeter - WebUI New - 12.jpg