Video Intercom/SIP 2.0/Multiple VTH and VTO One-Key Config Setup

Revision as of 21:54, 1 November 2021 by William.V (talk | contribs)

(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)

How to Setup One Key Config

Description

This article will go over the new One Key Config setup with multiple devices.

Prerequisites

  • VTH with the One Key Config feature
  • VTOs with SIP 2.0 Firmware

Video Instructions

Step by Step Instructions

1. Select your region by tapping on the country

2.0 Multiple VDP One Key Config-1.png

2. Select the country and tap on OK

2.0 Multiple VDP One Key Config-2.png

3. Then tap on OK

2.0 Multiple VDP One Key Config-3.png

4. Tap on Villa before clicking on OK

2.0 Multiple VDP One Key Config-4.png

5. Select First-time Config and then OK

2.0 Multiple VDP One Key Config-5.png

6. The VTH will then receive a DHCP address from the network

2.0 Multiple VDP One Key Config-6.png

7. Click on Next or select Static IP if you have a specific IP to give it

2.0 Multiple VDP One Key Config-7.png

8. Set VTH Password Will initialize all the VTHs on the network with this password. Also enter an E-Mail to reset passwords. Tap on Next

Note: VTHs will require a 6-digit numerical password

2.0 Multiple VDP One Key Config-8.png

9. Set VTO Password Will initialize all the VTOs on the network with this password. The E-Mail will re-enter itself. Tap on Next

Note: The VTO password requires a 8-character password. The password must be alpha-numerical

2.0 Multiple VDP One Key Config-9.png

10. Click on Initialize on all the VDP devices on the network. The VTH will then initialize them with the passwords we previously entered.

2.0 Multiple VDP One Key Config-10.png

11. Make sure all units say Initialized before clicking on Next

2.0 Multiple VDP One Key Config-11.png

12. The VTH will now force a DHCP address to the VDP devices. It will also assign suggested main and subs to each device on the network.

2.0 Multiple VDP One Key Config-12.png

13. This page will require you to edit every device we initialized. Local is the VTH we are on. So you don't need to edit. Select the First VTO and tap on Edit

The VTH will suggest the Main/Sub devices but you will still need to tap edit on each one to confirm the setup. If you skip this step you may encounter an Environment error

2.0 Multiple VDP One Key Config-13.png

14. Make sure the first VTO is the Main unit. Change the video standard to NTSC for USA standards. Set the time and date to the VTO then tap on OK

2.0 Multiple VDP One Key Config-14.png

15. Now select the second VTO and tap on Edit

The VTH will suggest the Main/Sub devices but you will still need to tap edit on each one to confirm the setup. If you skip this step you may encounter an Environment error

2.0 Multiple VDP One Key Config-15.png

16. Enter a new IP if the DHCP address is not wanted. Then tap on OK

2.0 Multiple VDP One Key Config-16.png

17. Once you see all the VDP device say Change you can tap on One-key Config

2.0 Multiple VDP One Key Config-17.png

18. The VTH will now send the configurations to all the devices. The progress will stay stuck on a progress percentage until all the devices boot back up.

2.0 Multiple VDP One Key Config-18.png

19. Once the devices boot back up you will be sent to the VTH home page, Click on Monitor to make sure you can see all the VTO's we setup

2.0 Multiple VDP One Key Config-19.png

20. Tap on the entries

2.0 Multiple VDP One Key Config-20.png

21. If you can see video and initiate a two-way talk you know everything went through properly.

2.0 Multiple VDP One Key Config-21.png

22. VTHs can now receive calls from the VTOs

2.0 Multiple VDP One Key Config-22.png