Video Intercom/SIP 2.0/Stand Alone VTO2111D-WP SIP 2.0 Setup

These instructions are for Generation 2, IP-based Video Intercom Devices only.
Icon Name Generation Technology SIP 2.0 Example Device 1 Example Device 2 Identifying Characteristic PC Software Mobile App
Gen2-SIP2.0-IP Gen 2 IP SIP 2.0 VTH1550CH-S DHI-VTO2000A-S "-S" at end of model name DSS or DSS Express S DSS Mobile for VDP

Stand Alone VTO2111D-WP SIP 2.0 Setup

Description

This article will cover how to setup a VTO2111D-WP Video Intercom with SIP 2.0 Firmware standalone with iDMSS/gDMSS push notifications

Prerequisites

  • DHI-VTO2111D-WP with SIP 2.0 firmware
  • iDMSS Plus or gDMSS Plus

Video Instructions

Step by Step Instructions

1. Log into the web interface of the VTO2111D-WP

VTO2111D-WPStandaloneSetup1.png

2. Select "Network Setting"

VTO2111D-WPStandaloneSetup2.png

3. Under the "Basic" section, change the IP Address and network information for either the wired and/or wireless connection(s) to match your network's IP scheme.

If you plan to use just the wireless connection, select "WiFi" on the left and then select your wireless network and have the device connect to it. If you plan to use the wired connection, skip to the next step.

VTO2111D-WPStandaloneSetup3.png

4. In the "Basic" section, scroll down to "P2P" and check the box next to "Enable".
Select "Save" at the bottom.

VTO2111D-WPStandaloneSetup4.png

5. Open iDMSS Plus, if on iOS, or gDMSS Plus, if on Android. Then select the Home icon at the top left.

VTO2111D-WPStandaloneSetup5.png

6. Select the "Device" button at the bottom.

VTO2111D-WPStandaloneSetup6.png

7. Select the Plus button at the top right and then "SN/Scan".

VTO2111D-WPStandaloneSetup7.png

8. Use your mobile device's camera to scan the QR code that is on the VTO's web interface under P2P (See Step 4).

VTO2111D-WPStandaloneSetup8.png

9. Your VTO's serial number should have been populated on this page. If it is correct, select the "Next" button.

VTO2111D-WPStandaloneSetup9.png

10. Select the "Doorbell" icon.

VTO2111D-WPStandaloneSetup10.png

11. Give your VTO a name next to "Device Name". Then input the username next to "Username" and the password next to "Device Password".
After inputting all the correct information, select the Floppy Disk icon at the top right to save the settings.

VTO2111D-WPStandaloneSetup11.png

12. You should get a live view of your VTO. Feel free to test if the audio and unlocking mechanisms work.
When done testing, select the Back Arrow at the top left.

VTO2111D-WPStandaloneSetup12.png

13. Select "Message" at the bottom.

VTO2111D-WPStandaloneSetup13.png

14. Select the Bell With the Plus Symbol at the top left.

VTO2111D-WPStandaloneSetup14.png

15. Toggle the Enable switch next to your VTO in the list.

VTO2111D-WPStandaloneSetup15.png

16. Once it has been enabled sucessfully it will show "Subscribed successfully."

VTO2111D-WPStandaloneSetup16.png

17. Press the button on the front of the VTO.
If the app is open you will see the below screen with a view from your VTO.
If the app is not open, you should get a push notification. Select the push notification and you should see the below screen with a view from your VTO.
Select the Green Phone button to answer the call.

VTO2111D-WPStandaloneSetup17.png

VTO2111D-WPStandaloneSetup18.png