Difference between revisions of ":People Flow Control"
(→Setup People Flow Control) |
|||
| (19 intermediate revisions by the same user not shown) | |||
| Line 2: | Line 2: | ||
==Description== | ==Description== | ||
| + | These instructions will show how to setup the People Flow Control feature at the NVR's WebUI | ||
| + | |||
| + | For instructions on how to enable and use the People Flow Control at the NVR use the following link: | ||
| + | |||
| + | [[IVS:People Flow Control/Enable and Use Flow Control|How To Enable and Use Flow Control With the NVR]] | ||
| + | |||
==Prerequisites== | ==Prerequisites== | ||
| + | * DHI-NVR5216-16P-I with [https://dahuawiki.com/Thermal/DHI-NVR5216-16P-I_Firmware_Guide#Thermal_Solution_Firmware_for_DHI-ASI7213X-T1| latest firmware Thermal firmware] | ||
| + | * Camera added to NVR | ||
| + | * NVR configured and setup on network | ||
| + | * Local computer | ||
==Video Instructions== | ==Video Instructions== | ||
===Setup: WebUI=== | ===Setup: WebUI=== | ||
| Line 10: | Line 20: | ||
==Step by Step Instructions== | ==Step by Step Instructions== | ||
| − | ===Setup | + | ===Setup People Counting=== |
1. Enter the IP address of the NVR into Internet Explorer | 1. Enter the IP address of the NVR into Internet Explorer | ||
| Line 18: | Line 28: | ||
[[File:IVS_-_People_Flow_Control_Setup_WebUI_-_1.jpg|800x800px]] | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_1.jpg|800x800px]] | ||
| + | |||
| + | 2. Click Management > Camera | ||
[[File:IVS_-_People_Flow_Control_Setup_WebUI_-_2.jpg|800x800px]] | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_2.jpg|800x800px]] | ||
| + | |||
| + | 3. Under the Camera Registration list, confirm the Channel # the N45EJ62 is added as. In this example it is Channel 1 | ||
[[File:IVS_-_People_Flow_Control_Setup_WebUI_-_3.jpg|800x800px]] | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_3.jpg|800x800px]] | ||
| + | |||
| + | 4. From the Main Menu | ||
| + | |||
| + | Select '''AI''' | ||
[[File:IVS_-_People_Flow_Control_Setup_WebUI_-_4.jpg|800x800px]] | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_4.jpg|800x800px]] | ||
| + | |||
| + | 5. Select Parameters > Smart Plan | ||
[[File:IVS_-_People_Flow_Control_Setup_WebUI_-_5.jpg|800x800px]] | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_5.jpg|800x800px]] | ||
| + | |||
| + | 6. Use the dropdown box to select the channel | ||
| + | |||
| + | Click to select the People Counting feature | ||
[[File:IVS_-_People_Flow_Control_Setup_WebUI_-_6.jpg|800x800px]] | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_6.jpg|800x800px]] | ||
| + | |||
| + | Click '''OK''' to save | ||
[[File:IVS_-_People_Flow_Control_Setup_WebUI_-_7.jpg|800x800px]] | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_7.jpg|800x800px]] | ||
| + | |||
| + | 7. Select People Counting | ||
[[File:IVS_-_People_Flow_Control_Setup_WebUI_-_8.jpg|800x800px]] | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_8.jpg|800x800px]] | ||
| + | |||
| + | 8. Click the + to add a new People Counting rule | ||
[[File:IVS_-_People_Flow_Control_Setup_WebUI_-_9.jpg|800x800px]] | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_9.jpg|800x800px]] | ||
| + | |||
| + | 9. Click Draw Area to draw the detection zone for the People Counting | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_10.jpg|800x800px]] | ||
| + | |||
| + | Left click inside the image to begin drawing the Area | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_11.jpg|800x800px]] | ||
| + | |||
| + | Drag and left click to create a complete object | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_12.jpg|800x800px]] | ||
| + | |||
| + | Complete | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_13.jpg|800x800px]] | ||
| + | |||
| + | People Counting Alarm | ||
| + | |||
| + | Adjust parameters as desired for alarm events: | ||
| + | |||
| + | * Enter No. | ||
| + | * Exit No. | ||
| + | * Strand No. | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_14.jpg|800x800px]] | ||
| + | |||
| + | Click More Setting | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_15.jpg|800x800px]] | ||
| + | |||
| + | For additional options for output when a people counting alarm is triggered | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_16.jpg|800x800px]] | ||
| + | |||
| + | Click Draw Rule to draw the line which people need to cross to trigger the People Counting feature | ||
| + | |||
| + | The direction of the arrow on this line will determine the direction of Enter / Exit that is counted | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_17.jpg|800x800px]] | ||
| + | |||
| + | Left click and '''drag down''' to create a '''left facing arrow''' | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_18.jpg|800x800px]] | ||
| + | |||
| + | Left click and '''drag up''' to create a '''right facing arrow''' | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_19.jpg|800x800px]] | ||
| + | |||
| + | Click '''OK''' to save | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_20.jpg|800x800px]] | ||
| + | |||
| + | ===Setup Queuing=== | ||
| + | 1. Select the Queuing tab | ||
| + | |||
| + | Click the + to create a new rule | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_21.jpg|800x800px]] | ||
| + | |||
| + | 2. Check the box to enable | ||
| + | |||
| + | Enter a value in the Queue People No. field | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_22.jpg|800x800px]] | ||
| + | |||
| + | 3. Click Draw Area | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_23.jpg|800x800px]] | ||
| + | |||
| + | 4. Left click and drag to draw the detection area | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_24.jpg|800x800px]] | ||
| + | |||
| + | 5. Click '''OK''' to save | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_25.jpg|800x800px]] | ||
| + | |||
| + | ===Setup People Flow Control=== | ||
| + | 1. Select the '''People Flow Control''' tab | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_26.jpg|800x800px]] | ||
| + | |||
| + | 2. The parameters here determine what will trigger an alarm event for People Flow Control | ||
| + | |||
| + | Click the '''Setting''' button to select the channel to display On Screen Statistics (green People Counting statistics overlay) | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_27.jpg|800x800px]] | ||
| + | |||
| + | 3. Select the channel | ||
| + | |||
| + | Click '''OK''' to save | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_28.jpg|800x800px]] | ||
| + | |||
| + | 4. The alarm is triggered when the number of people staying in the area is greater than the '''Threshold''' value | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_26-2.jpg|800x800px]] | ||
| + | |||
| + | 5. By default the On Screen Display statistics will automatically clear: | ||
| + | |||
| + | * When the device is rebooted | ||
| + | * When the system time passes to next day (0:00 am) | ||
| + | |||
| + | Set a custom time for clearing the OSD statistics by modifying the ''Num Auto-Clear Time'' field | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_26-1.jpg|800x800px]] | ||
| + | |||
| + | 6. Click '''OK''' to save all settings | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_29.jpg|800x800px]] | ||
| + | |||
| + | |||
| + | ''Both rules configured and displayed at Live View on WebUI of NVR: | ||
| + | '' | ||
| + | |||
| + | [[File:IVS_-_People_Flow_Control_Setup_WebUI_-_30.jpg|800x800px]] | ||
Latest revision as of 16:19, 25 June 2020
Contents
People Flow Control
Description
These instructions will show how to setup the People Flow Control feature at the NVR's WebUI
For instructions on how to enable and use the People Flow Control at the NVR use the following link:
How To Enable and Use Flow Control With the NVR
Prerequisites
- DHI-NVR5216-16P-I with latest firmware Thermal firmware
- Camera added to NVR
- NVR configured and setup on network
- Local computer
Video Instructions
Setup: WebUI
Enable and Use Flow Control: SystemUI
Step by Step Instructions
Setup People Counting
1. Enter the IP address of the NVR into Internet Explorer
Enter the username/password for the device
Click Login
2. Click Management > Camera
3. Under the Camera Registration list, confirm the Channel # the N45EJ62 is added as. In this example it is Channel 1
4. From the Main Menu
Select AI
5. Select Parameters > Smart Plan
6. Use the dropdown box to select the channel
Click to select the People Counting feature
Click OK to save
7. Select People Counting
8. Click the + to add a new People Counting rule
9. Click Draw Area to draw the detection zone for the People Counting
Left click inside the image to begin drawing the Area
Drag and left click to create a complete object
Complete
People Counting Alarm
Adjust parameters as desired for alarm events:
- Enter No.
- Exit No.
- Strand No.
Click More Setting
For additional options for output when a people counting alarm is triggered
Click Draw Rule to draw the line which people need to cross to trigger the People Counting feature
The direction of the arrow on this line will determine the direction of Enter / Exit that is counted
Left click and drag down to create a left facing arrow
Left click and drag up to create a right facing arrow
Click OK to save
Setup Queuing
1. Select the Queuing tab
Click the + to create a new rule
2. Check the box to enable
Enter a value in the Queue People No. field
3. Click Draw Area
4. Left click and drag to draw the detection area
5. Click OK to save
Setup People Flow Control
1. Select the People Flow Control tab
2. The parameters here determine what will trigger an alarm event for People Flow Control
Click the Setting button to select the channel to display On Screen Statistics (green People Counting statistics overlay)
3. Select the channel
Click OK to save
4. The alarm is triggered when the number of people staying in the area is greater than the Threshold value
5. By default the On Screen Display statistics will automatically clear:
- When the device is rebooted
- When the system time passes to next day (0:00 am)
Set a custom time for clearing the OSD statistics by modifying the Num Auto-Clear Time field
6. Click OK to save all settings
Both rules configured and displayed at Live View on WebUI of NVR:
