-
...nt is 8 when the device is shipped out of the factory. The factory default setup includes two levels: user and admin. You can set the corresponding group an
Please note the user rights shall not exceed the group right setup.
3 KB (444 words) - 23:13, 11 August 2016
-
Here you can set device alarm type and alarm sound setup.
...splayed, when alarm is triggered, there will be no image prompt, but alarm record will be in list on the right.
2 KB (228 words) - 22:51, 11 August 2016
-
* Select date. If you do not select, current setup applies to today only. You can select all week column to apply to the whole
Record
4 KB (598 words) - 19:32, 15 August 2019
-
*[[DSS/V8/DSS_Express/Instruction/Storage|Setup Local Storage in DSS Express V8]]
*[[DSS/V8/DSS_Express/Instruction/Local_Recording_Schedule|Setup Recording schedule in DSS Express V8]]
14 KB (2,112 words) - 19:01, 5 January 2024
-
===How to Configure IP Camera to Record to SD-Card===
2. Click, "Setup"
881 bytes (125 words) - 23:04, 11 August 2016
-
==How to Configure SmartPSS to Record IP Camera Feed / PC-NVR Setup==
4. Click the device you wish to setup to record.
2 KB (310 words) - 18:22, 2 March 2021
-
==How to setup NAS Storage==
====NAS Storage Setup====
1 KB (172 words) - 22:11, 6 August 2019
-
=Initial Setup=
* [[IPCRemoteAccess | How to setup remote access for IP Camera(StandAlone)]]
9 KB (978 words) - 18:28, 14 June 2016
-
==Setup==
* [[IPCRecordPath | Record Path]]
4 KB (328 words) - 05:56, 15 August 2016
-
...uced. Usually we do not modify it. Of course, we can use COM to change its setup.
; Pre-Record
16 KB (2,651 words) - 18:05, 15 August 2016
-
...e camera from no-WDR mode to the WDR mode, system may lose several seconds record video.
...y/night''': It is to set device color and the B/W mode switch. The default setup is auto.
4 KB (722 words) - 05:06, 15 August 2016
-
Activate current control, modify setup, and then move up and down.
Record
25 KB (3,410 words) - 19:15, 1 July 2016
-
==Schedule Record==
==Schedule Record Setup for Web service==
4 KB (574 words) - 00:11, 7 February 2020
-
===Snapshot Setup on NVR===
...tions below to setup Snapshot recording on your recorder. You will need to setup an event on a camera or recorder in order for snapshot to occur.
2 KB (276 words) - 23:11, 2 November 2020
-
...evice directly. Here you can set TCP/UPD/auto connection mode. The default setup is TCP.
...e camera from no-WDR mode to the WDR mode, system may lose several seconds record video.
10 KB (1,675 words) - 19:12, 15 August 2016
-
...e via etho0 or the eth1. Usually you need to set one default card (default setup is etho) to request the auto network service form the device-end such as DH
...may pop up dialog box for you to confirm setup when you want to change MTU setup. Click OK button to confirm current reboot, or you can click Cancel button
22 KB (3,608 words) - 20:41, 7 December 2022
-
...C button to exit the region setup interface system will not save your zone setup.
...signal at the fifth second, the buzzer, tour, PTZ　activation, snapshot, record channel will begin another 10s while the screen prompt, alarm upload, email
15 KB (2,430 words) - 20:48, 3 December 2020
-
====Record====
The record type priority is: Alarm>Motion>Regular
5 KB (719 words) - 19:12, 15 August 2016
-
* Pack duration: Here is for you to specify record duration. The value ranges from 0 to 120 minutes. Default value is 60 minut
* Pack duration: Here is for you to specify record duration. The value ranges from 1 to 120 minutes. Default value is 60 minut
13 KB (2,073 words) - 19:11, 15 August 2016
-
==Setup Audio Recording==
Record Audio in addition to video.
746 bytes (103 words) - 23:45, 2 November 2020
