IVS:Face Detect

From Dahua Wiki

Jump to: navigation, search

Face Detect

Description

Face detection is to detect if there is any human face appearing in the video, and capture the face then send it to the NVR for analysis and processing, it can activate snapshot, record and alarm.

FaceDetect.png

Example Photos of Distance Requirements

Installation Requirements

Face Detect Install Requirements.png

The horizontal distance between camera and monitoring target is d(m), the camera installation height is h(m), depression angle of camera is α(degree) (it is the included angle between the camera monitoring direction and horizontal surface). You can refer to the following parameter table:

Parameter Recommended value Range
Height h(m) 2.5 2~3
Horizontal distance d(m) 6 4~20
α(degree) ≤15 10~15

If the actual situation fails to meet the settings recommended in the table above, you can refer to the table below. Select the most suitable parameter configuration if it can guarantee that the face pixel is more than 150 x 150 (it can reach 200 x 200 ideally) in 1080P.

Height(m) Horizontal distance(m)
2 4~20
2.25 5~20
2.5 6~20
2.75 7~20
3 8~20

Installation Testing

Face Detect Install Scene.png

1. Select test point (it is recommended to select the test point where there is good light, try to avoid backlight and sidelight), lay a camera in the location which is d meters horizontally away from the test point, the fixed height is h meters. (please select d and h according to the table above)

2. Installation person A stands in the test point, look ahead horizontally, installation person B will adjust the IPC; Adjust the camera angle, monitoring range, focal length until it meets the following requirements:

a) The human face is in the center of the image, and it is clear.

b) Make sure the width of the face is more than 150 x 150 pixel in 1080P resolution (take snapshot via IPC web, use paint tool to check image pixel, the distance between the center of both eyes is required to be more than 50 pixels.)

3. Make sure the requirements above should be satisfied, and then fix the camera and lens. The installation person A passes the monitoring point from far to near, installation person B checks the monitoring image to make sure it can acquire front, clear face whose width and height is bigger than 150 pixels when person A is passing monitoring point, then it means the installation is successful. The ideal monitoring effect is shown in the above image.

Internet Explorer Setup

Prerequisites

  • Intelligent Network Camera.
  • Updated firmware that supports intelligent features.
  • Internet Explorer.

IVS Best Practices

To assess issues with IVS compatibility between the camera and NVR, please update both devices to the most current firmware and factory reset the NVR, and use the hard reset button to reset the camera.

Video Instructions

Step by Step Instructions

1. Click “Enable”.

Face Detect1.png

2. Click face enhancement to enhance the face image display.

Face Detect2.png

3. Select max and min size, draw max and min target for target filtering. This step is to filter target, which can’t be operated under default status.

Face Detect3.png

4. Activate record, alarm, email and snapshot according to the requirements.

Face Detect4.png

5. Target filter can set max target and min target, which means it can detect max and min target.

Face Detect5.png

6. Click ok to complete settings.

Face Detect6.png

System Interface Setup

Prerequisites

Video Instructions

Step by Step Instructions

1. Go to Event.

IntrusionSetupSystem1.png

2. Enable Face detect under IVS and then hit apply and save.

FaceDetectionSetupSystem2.png

SmartPSS Setup

Prerequisites

  • SmartPSS 2.0
  • IVS capable device with Face Detection
  • Upgraded devices to latest firmware

Smart PSS Video Instructions

Step by Step Instructions

1. Launch and Log into Smart PSS

smartpss2facedetect2.png

2. Select "Live".

smartpss2facedetectv1.png

3. From Live View Select Device that is IVS capable -> right click on device and select IVS Config.

smartpss2facedetectv3.png

4. Select Face detection -> Select Next.

smartpss2facedetectv4.png

5.Draw a Detection Zone

smartpss2facedetectv5.png

6. Select Config for arming schedule and choose what days Face Detect is to be enabled.

smartpss2facedetectv6.png

7. Select Alarm -> Choose alarm type such as Record -> Select Save

smartpss2facedetectv7.png

8.Select Target Filter -> Select Enable -> Choose either "Width and Height or Width and Height" -> Select Draw to size the target filter (Inner green box size is minimum target, Outer green box is the maximum target) -> Apply and Save.

smartpss2facedetectv8.png