|
|
| (One intermediate revision by the same user not shown) |
| Line 1: |
Line 1: |
| | ==Reset IP Camera== | | ==Reset IP Camera== |
| − | Reset Instruction of Network Camera
| |
| − |
| |
| − | This document includes the information of the reset operation and the position of reset button of
| |
| − | the network cameras.
| |
| − |
| |
| − | 1. THE OPERATION OF RESET
| |
| − |
| |
| − | 1.1 The camera should connect power, click the reset button for at least 5 seconds until the
| |
| − | camera restart, and then the camera will restore factory default setup.
| |
| − | <br> If there is a PWR indicator, you can check the indicator go off and on again.
| |
| − | <br> If it is a IR camera, you can check the IR LED turn on again.
| |
| − | <br> For others situation, keep the operation long enough to make sure the camera restart.
| |
| − |
| |
| − | 1.2 Most of the reset is a button, but some of them are just terminals or cables that you need to
| |
| − | do a shortage to finish this operation. You will see some samples below.
| |
| − |
| |
| − | 2. THE POSITION OF THE RESET
| |
| − | <br>Mainly it depends on the type of the camera, when you see the appearance you can make a
| |
| − | judge accordingly. The types of the IP camera are listed below:
| |
| − |
| |
| − | 2.1 Indoor Fixed Network Camera
| |
| − | <br>Appearance:
| |
| − | <br>These kinds of IP cameras, the reset button is always on the back panel of the camera, with a
| |
| − | mark “RESET”
| |
| − | <br>Models:
| |
| − | *IPC-HF3500 series
| |
| − | *IPC-HF3300 series
| |
| − | *IPC-HF3301 series
| |
| − | *IPC-HF3200 series
| |
| − | *IPC-HF3211 series
| |
| − | *IPC-HF3100 series
| |
| − | *IPC-HF3110 series
| |
| − | *IPC-HF3101 series
| |
| − |
| |
| − | The pictures below are the sample of back panel. (The appearance may not exactly the same)
| |
| − |
| |
| − | 2.2 IR waterproof fixed network camera.
| |
| − |
| |
| − | Some of these cameras (earlier models) were combined with Multiple-function combination
| |
| − | Cable that you need to do a shortage to reset.
| |
| − |
| |
| − | Appearance:
| |
| − | <br>Models:
| |
| − | *HFW3300 series
| |
| − | *HFW3110 series
| |
| − |
| |
| − | The picture below is the cable coming out of the camera; you need an extension cable to
| |
| − | do the reset. Shortage the Blue wire (RESET) and the Orange wire (GND) for at least 5
| |
| − | seconds until the camera restart.
| |
| − | Multiple combination cable and MD9M cable MD9M cable connector
| |
| − | 2.3 IR Waterproof Fixed Network Camera (With Integrated Bracket)
| |
| − | Appearance:
| |
| − | A. Most of this kind of camera, there will be a multiple-function combination cable coming
| |
| − | out of the bottom of the bracket. You can find one that is the reset cable.
| |
| − | Models:
| |
| − | IPC-HFW3300C
| |
| − | IPC-HFW3200C
| |
| − | IPC-HFW3202C
| |
| − | IPC-HFW3100C
| |
| − | IPC-HFW3101C
| |
| − | The pictures below are the sample of multi-function cable, and the reset is a button. (The
| |
| − | appearance may not exactly the same)
| |
| − | B. Some earlier models
| |
| − | There is also a multiple-function combination cable; the reset terminal is together with
| |
| − | the alarm terminal (you can find the label), you need shortage the RESET and GND pin
| |
| − | (7&6 in the picture below) for at least 5 seconds to make a reset.
| |
| − | 2.4 Mini IR Waterproof Fixed Network Camera (With Integrated Bracket)
| |
| − | Appearance:
| |
| − | Models:
| |
| − | IPC-HFW3200SP/N series
| |
| − | IPC-HFW2100S series
| |
| − | The reset button is inside of the camera, open the lens cap and you will find it.
| |
| − | 2.5 ( IR) Vandal Proof Network Dome Camera (and In-ceiling model)
| |
| − | Appearance:
| |
| − | Models:
| |
| − | IPC-HD/HDW3100 series
| |
| − | IPC-HD/HDW3200 series
| |
| − | IPC-HDB/HDBW3202 series
| |
| − | IPC-HDB/HDBW3101 series
| |
| − | IPC-HDB/ HDBW5100 series
| |
| − | IPC-HDB/ HDBW5200 series
| |
| − | IPC-HDB/HDBW 3202-DI series (DI means in-ceiling model)
| |
| − | IPC-HDB/HDBW 3200-DI series
| |
| − | IPC-HDB/HDBW 3101-DI series
| |
| − | IPC-HDB/HDBW 3100-DI series
| |
| − | The reset button is inside of the camera, open the dome camera enclosure; you will find it
| |
| − | next to the alarm terminals (see the picture below).
| |
| − | 2.6 Mini dome
| |
| − | Appearance：
| |
| − | Models：
| |
| − | IPC-HDB3200C series
| |
| − | IPC-HDB3100C series
| |
| − | IPC-HD2100C series
| |
| − | The reset is inside the camera, open the dome camera enclosure and you can find it.
| |
| − | 2.7 Mobile Network Camera (and some dome network camera)
| |
| − | Appearance：
| |
| − | Models：
| |
| − | IPC-HDW2100-M
| |
| − | IPC-HDW2100 Series
| |
| − | IPC-HDW2200S
| |
| − | IPC-HDW3300S
| |
| − | The reset button is inside of the camera, open the dome camera enclosure and will find it
| |
| − | under the IR board.(see picture below)
| |
| − | 2.8 Home use series
| |
| − | Appearance:
| |
| − | This type of network camera is very simple and small, and there reset button is mostly on
| |
| − | the back or side of the camera.
| |
| − | a. K100 series (on the back)
| |
| − | A6 series (on the side)
| |
| − | A7 series (on the back)
| |
| − | A8 series (back in the cover)
| |
| − | Note: For the models not included, you can check the appearance as a reference.
| |
| − |
| |
| | | | |
| | <pdf>File:ResetIPCamera.pdf</pdf> | | <pdf>File:ResetIPCamera.pdf</pdf> |
| | | | |
| | + | <br> |
| | [[File:hardreset001.png]] | | [[File:hardreset001.png]] |
| | | | |
