Difference between revisions of "SmartPSS/Face Detect"
| (6 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| + | =='''NOTICE'''== | ||
| + | [https://dahuawiki.com/Discontinuation_of_SmartPSS Notice of Discontinuation of SmartPSS] | ||
| + | |||
==How To Use Face Detect In SmartPSS== | ==How To Use Face Detect In SmartPSS== | ||
| Line 6: | Line 9: | ||
===Prerequisites=== | ===Prerequisites=== | ||
* [https://dahuawiki.com/Template:SmartPSS SmartPSS] | * [https://dahuawiki.com/Template:SmartPSS SmartPSS] | ||
| − | * Supported device with Face Detect feature | + | * Supported device with Face Detect feature |
* Device added to SmartPSS Device List - [[SmartPSS/Add Device via IP|How To Add Device to SmartPSS]] | * Device added to SmartPSS Device List - [[SmartPSS/Add Device via IP|How To Add Device to SmartPSS]] | ||
| − | |||
| − | |||
| − | |||
===Step by Step Instructions=== | ===Step by Step Instructions=== | ||
| Line 16: | Line 16: | ||
[[File:Preset_SmartPSS_1.jpg|600px]] | [[File:Preset_SmartPSS_1.jpg|600px]] | ||
| + | |||
| + | 2. Click Device CFG | ||
| + | |||
| + | [[File:Face_Detect_SmartPSS2_-_1.jpg|600px]] | ||
| + | |||
| + | 3. Click to select the device from the device tree on the left | ||
| + | |||
| + | [[File:Face_Detect_SmartPSS2_-_2.jpg|600px]] | ||
| + | |||
| + | 4. Click the Event tab | ||
| + | |||
| + | [[File:Face_Detect_SmartPSS2_-_3.jpg|600px]] | ||
| + | |||
| + | |||
| + | 5. Click the Intelligent to open IVS Rule Setup | ||
| + | |||
| + | [[File:Face_Detect_SmartPSS2_-_4.jpg|600px]] | ||
| + | |||
| + | |||
| + | 6. In the pop up menu that appears, first select the Channel No. you wish to configure then click OK | ||
| + | |||
| + | [[File:Face_Detect_SmartPSS2_-_5.jpg|600px]] | ||
| + | |||
| + | 7. On the Smart Plan page, if an existing rule is already setup (highlighted) click it once to de-select | ||
| + | |||
| + | [[File:Face_Detect_SmartPSS2_-_6.jpg|600px]] | ||
| + | |||
| + | Then click to select the Face Detect icon then click Next | ||
| + | |||
| + | [[File:Face_Detect_SmartPSS2_-_7.jpg|600px]] | ||
| + | |||
| + | |||
| + | |||
| + | 8.Click the checkbox to Enable the rule. To draw the detection zone for Face Detection click 'Re-draw' | ||
| + | |||
| + | [[File:Face_Detect_SmartPSS2_-_8.jpg|600px]] | ||
| + | |||
| + | 9. Left click inside the video frame to draw the detection zone. | ||
| + | |||
| + | [[File:Face_Detect_SmartPSS2_-_9.jpg|600px]] | ||
| + | |||
| + | |||
| + | Once finished Right click to complete the zone | ||
| + | |||
| + | |||
| + | [[File:Face_Detect_SmartPSS2_-_10.jpg|600px]] | ||
| + | |||
| + | |||
| + | 10. To set a schedule for the IVS Face Detect Rule click the Config button | ||
| + | |||
| + | [[File:Face_Detect_SmartPSS2_-_11.jpg|600px]] | ||
| + | |||
| + | 11. Use the menu to configure a schedule for the IVS rule. By default it will be set to 24/7. Click Save once the schedule has been set. | ||
| + | |||
| + | [[File:Face_Detect_SmartPSS2_-_12.jpg|600px]] | ||
| + | |||
| + | |||
| + | 12. Click Save to finish creating the IVS Face Detect rule | ||
| + | |||
| + | [[File:Face_Detect_SmartPSS2_-_13.jpg|600px]] | ||
| + | |||
| + | [[Category:IVS]] | ||
| + | [[Category:SmartPSS]] | ||
| + | [[Category:How To]] | ||
| + | [[Category:Face Detection]] | ||
Latest revision as of 23:26, 2 October 2024
Contents
NOTICE
Notice of Discontinuation of SmartPSS
How To Use Face Detect In SmartPSS
Description
This article will show you how to use the Face Detect feature on a supported device using SmartPSS
Prerequisites
- SmartPSS
- Supported device with Face Detect feature
- Device added to SmartPSS Device List - How To Add Device to SmartPSS
Step by Step Instructions
1. Launch SmartPSS.
2. Click Device CFG
3. Click to select the device from the device tree on the left
4. Click the Event tab
5. Click the Intelligent to open IVS Rule Setup
6. In the pop up menu that appears, first select the Channel No. you wish to configure then click OK
7. On the Smart Plan page, if an existing rule is already setup (highlighted) click it once to de-select
Then click to select the Face Detect icon then click Next
8.Click the checkbox to Enable the rule. To draw the detection zone for Face Detection click 'Re-draw'
9. Left click inside the video frame to draw the detection zone.
Once finished Right click to complete the zone
10. To set a schedule for the IVS Face Detect Rule click the Config button
11. Use the menu to configure a schedule for the IVS rule. By default it will be set to 24/7. Click Save once the schedule has been set.
12. Click Save to finish creating the IVS Face Detect rule
