Difference between revisions of "NVR/Recording Setup/Alarm Recording Setup SmartPSS 1.6"
| (One intermediate revision by one other user not shown) | |||
| Line 1: | Line 1: | ||
| + | =='''NOTICE'''== | ||
| + | [https://dahuawiki.com/Discontinuation_of_SmartPSS Notice of Discontinuation of SmartPSS] | ||
| + | |||
==How to set up alarm recording for physical alarm via SmartPSS 1.16== | ==How to set up alarm recording for physical alarm via SmartPSS 1.16== | ||
| Line 41: | Line 44: | ||
4. Log into SmartPSS -> Device CFG. | 4. Log into SmartPSS -> Device CFG. | ||
| − | [[ | + | [[File:Alarmsmartpss1_16.png|600px]] |
| − | [[ | + | [[File:Alarmsmartpss1_16_3.png|600px]] |
5. From left hand side select recorder -> Under event select alarm. | 5. From left hand side select recorder -> Under event select alarm. | ||
| − | [[ | + | [[File:Alarmsmartpss1_16_4.png|600px]] |
6. Check mark Alarm Input Enable -> Select channel. | 6. Check mark Alarm Input Enable -> Select channel. | ||
| − | [[ | + | [[File:Alarmsmartpss1_16_5.png|600px]] |
7. Select either, "NO" or "NC" | 7. Select either, "NO" or "NC" | ||
| Line 59: | Line 62: | ||
</gallery> | </gallery> | ||
| − | [[ | + | [[File:Alarmsmartpss1_16_6.png|600px]] |
8. Next select what actions you want the system to perform, when the alarm is activated. To record the alarm event you will need to check mark "record channel". | 8. Next select what actions you want the system to perform, when the alarm is activated. To record the alarm event you will need to check mark "record channel". | ||
| − | [[ | + | [[File:Alarmsmartpss1_16_8.png|600px]] |
9. Select Apply and Save to save settings. | 9. Select Apply and Save to save settings. | ||
| − | [[ | + | [[File:Alarmsmartpss1_16_9.png|600px]] |
10. Next you will need to set the schedule to record the alarm event. From the home page and select "Device CFG" | 10. Next you will need to set the schedule to record the alarm event. From the home page and select "Device CFG" | ||
| − | [[ | + | [[File:Alarmsmartpss1_16_3.png|600px]] |
11. From the left hand side select recorder -> select + button to show cameras -> select the camera alarm was set for -> under storage you will select | 11. From the left hand side select recorder -> select + button to show cameras -> select the camera alarm was set for -> under storage you will select | ||
record. | record. | ||
| − | [[ | + | [[File:Alarmsmartpss1_16_10.png|600px]] |
12. Select the gear icon -> Here you will see Period 1 (By default it will be set 0-24 hours. For this tutorial we are setting 1 Period -> Check mark "Alarm" -> Check mark "all" to record everyday of the week. | 12. Select the gear icon -> Here you will see Period 1 (By default it will be set 0-24 hours. For this tutorial we are setting 1 Period -> Check mark "Alarm" -> Check mark "all" to record everyday of the week. | ||
| − | [[ | + | [[File:Alarmsmartpss1_16_11.png|600px]] |
| − | [[ | + | [[File:Alarmsmartpss1_16_12.png|600px]] |
13. Here on the schedule you should see red for each day of the week as pictured below. Select apply and save to save settings. | 13. Here on the schedule you should see red for each day of the week as pictured below. Select apply and save to save settings. | ||
| − | [[ | + | [[File:Alarmsmartpss1_16_13.png|600px]] |
Latest revision as of 22:13, 2 October 2024
Contents
NOTICE
Notice of Discontinuation of SmartPSS
How to set up alarm recording for physical alarm via SmartPSS 1.16
Description
How to Setup Alarm Recording Using A Physical Alarm via SmartPSS 1.16
Prerequisites
- SmartPSS 1.16 or 1.161
- A NVR or IP Camera with an Alarm Out
- A low voltage physical alarm
- Dual pair 24 gauge run to the physical alarm
- Alarm block
Video Instructions
Step by Step Instructions
1. Identify which alarm out block you wish to use to connect your physical alarm. For this example we are going to use, "Alarm Out Channel 1"
2. Connect the cable to your physical alarm.
->
3. Connect the cable to the alarm block on the ports labeled, "IN1" and "Ground"
4. Log into SmartPSS -> Device CFG.
5. From left hand side select recorder -> Under event select alarm.
6. Check mark Alarm Input Enable -> Select channel.
7. Select either, "NO" or "NC"
NO -Normally Open
NC -Normally Close
8. Next select what actions you want the system to perform, when the alarm is activated. To record the alarm event you will need to check mark "record channel".
9. Select Apply and Save to save settings.
10. Next you will need to set the schedule to record the alarm event. From the home page and select "Device CFG"
11. From the left hand side select recorder -> select + button to show cameras -> select the camera alarm was set for -> under storage you will select record.
12. Select the gear icon -> Here you will see Period 1 (By default it will be set 0-24 hours. For this tutorial we are setting 1 Period -> Check mark "Alarm" -> Check mark "all" to record everyday of the week.
13. Here on the schedule you should see red for each day of the week as pictured below. Select apply and save to save settings.
