Difference between revisions of "Thermal/Temperature Monitoring/3rd Party VMS/Milestone/Configure Milestone"
(→Alarm configuration) |
(→Add device in Milestone XProtect Management Client) |
||
(4 intermediate revisions by the same user not shown) | |||
Line 9: | Line 9: | ||
===Add device in Milestone XProtect Management Client=== | ===Add device in Milestone XProtect Management Client=== | ||
− | 1. Add Device to Recording Server | + | 1. Add Device to Recording Server by left clicking Recording Servers |
+ | |||
+ | Right click the server | ||
+ | |||
+ | Select '''Add Hardware''' | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_1.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_1.jpg|800px]] | ||
+ | |||
+ | 2. Select Manual Add | ||
+ | |||
+ | Click '''Next''' | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_2.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_2.jpg|800px]] | ||
+ | 3. Click '''Add''' | ||
+ | |||
+ | Enter the username and password for the camera | ||
+ | |||
+ | Click Next | ||
+ | |||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_3.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_3.jpg|800px]] | ||
+ | |||
+ | 4. Select ONVIF for device driver | ||
+ | |||
+ | Click Next | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_4.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_4.jpg|800px]] | ||
+ | |||
+ | 5. Enter the IP address of the camera | ||
+ | |||
+ | Select (Auto-detect) | ||
+ | |||
+ | Click '''Next''' | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_5.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_5.jpg|800px]] | ||
+ | |||
+ | The software will automatically detect the camera | ||
+ | |||
+ | Click '''Next''' | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_6.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_6.jpg|800px]] | ||
+ | |||
+ | Click '''Next''' | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_6-1.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_6-1.jpg|800px]] | ||
+ | |||
+ | 6. Check the box to enable all Hardware for the camera | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_7.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_7.jpg|800px]] | ||
+ | |||
+ | Click '''Next''' | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_7-1.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_7-1.jpg|800px]] | ||
+ | |||
+ | Click '''Finish''' | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_8.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_8.jpg|800px]] | ||
+ | |||
+ | The camera will appear in the list | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_9.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_9.jpg|800px]] | ||
+ | ===Add event in Milestone XProtect Management Client=== | ||
+ | 1. Select Cameras | ||
− | + | Then left click to select the Thermal camera in the list | |
+ | |||
+ | Click the Events tab | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_10.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_10.jpg|800px]] | ||
+ | |||
+ | 2. Click Add to create a new Event | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_11.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_11.jpg|800px]] | ||
+ | |||
+ | 3. Find and select Temperature Detection Started in the list | ||
+ | |||
+ | Click '''OK''' | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_12.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_12.jpg|800px]] | ||
+ | |||
+ | 4. Repeat the process again to create a new Event | ||
+ | |||
+ | * Click Add | ||
+ | * Select Temperature Detection Stopped | ||
+ | * Click OK | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_13.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_13.jpg|800px]] | ||
+ | |||
+ | 5. Left click to select the 2nd channel of the Thermal camera | ||
+ | |||
+ | Repeat the previous steps on the 2nd channel to configure both events | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_14.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_14.jpg|800px]] | ||
+ | |||
+ | Temperature Detection Started / Temperature Detection Stopped Event configured on 2nd channel: | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_15.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_15.jpg|800px]] | ||
===Add rules for event=== | ===Add rules for event=== | ||
+ | 1. Select Rules | ||
+ | |||
+ | Right click Rules | ||
+ | |||
+ | Select Add Rule | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_16.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_16.jpg|800px]] | ||
+ | |||
+ | 2. Enter a name for the Rule | ||
+ | |||
+ | Click event | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_17.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_17.jpg|800px]] | ||
+ | |||
+ | 3. Select Devices > Configurable Events | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_18.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_18.jpg|800px]] | ||
+ | |||
+ | Find Temperature Detection Started in the list and click to select | ||
+ | |||
+ | Click OK | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_19.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_19.jpg|800px]] | ||
+ | |||
+ | 4. Click devices/recording/server/managementserver | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_20.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_20.jpg|800px]] | ||
+ | |||
+ | 5. Left click to select the Thermal camera in the list | ||
+ | |||
+ | Click Add | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_20-1.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_20-1.jpg|800px]] | ||
+ | |||
+ | 6. Repeat the process for the 2nd channel | ||
+ | |||
+ | Click OK | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_21.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_21.jpg|800px]] | ||
+ | |||
+ | 7. Click Next | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_22.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_22.jpg|800px]] | ||
+ | |||
+ | 8. Configure the schedule for the event | ||
+ | |||
+ | In this example we select All days by clicking Day of week is then selecting all Days | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_23.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_23.jpg|800px]] | ||
+ | |||
+ | 9. Click Next | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_24.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_24.jpg|800px]] | ||
+ | |||
+ | 10. Select action to perform when the event is triggered | ||
+ | |||
+ | In this example we select | ||
+ | |||
+ | * Record - Start recording on <devices> | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_25.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_25.jpg|800px]] | ||
+ | |||
+ | * Log - Make new <log entry> | ||
+ | |||
+ | Click logentry | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_26.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_26.jpg|800px]] | ||
+ | |||
+ | 11. Click to add each type of System Information to the log template | ||
+ | |||
+ | Click OK | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_27.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_27.jpg|800px]] | ||
+ | |||
+ | Click Next | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_28.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_28.jpg|800px]] | ||
+ | |||
+ | 12. Select Perform stop action on <event> | ||
+ | |||
+ | Click Next | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_29.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_29.jpg|800px]] | ||
+ | |||
+ | 13. Click Finish | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_30.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_30.jpg|800px]] | ||
===Alarm configuration=== | ===Alarm configuration=== | ||
+ | 1. Select Alarm Definitions | ||
+ | |||
+ | Right click Alarm Definitions | ||
+ | |||
+ | Select Add New | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_31.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_31.jpg|800px]] | ||
+ | |||
+ | 2. Check to Enable | ||
+ | |||
+ | Enter a name - Temperature Detection Start | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_32.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_32.jpg|800px]] | ||
+ | |||
+ | 3. Use the dropdown box next to Triggering event to select Device Events | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_33.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_33.jpg|800px]] | ||
+ | |||
+ | Use the dropdown box to select TemperatureStart | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_34.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_34.jpg|800px]] | ||
+ | |||
+ | 4. Click Select to select which devices for use with the alarm | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_35.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_35.jpg|800px]] | ||
+ | |||
+ | 5. Select the Thermal camera in the list, click Add | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_36.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_36.jpg|800px]] | ||
+ | |||
+ | 6. Repeat the process for the 2nd channel of the camera | ||
+ | |||
+ | Click OK | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_37.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_37.jpg|800px]] | ||
+ | |||
+ | 7. Click Save | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_38.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_38.jpg|800px]] | ||
+ | |||
+ | 8. Another rule must be created for the event end | ||
+ | |||
+ | Right click Alarm Definitions | ||
+ | |||
+ | Select Add New | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_39.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_39.jpg|800px]] | ||
+ | |||
+ | 9. Click to Enable | ||
+ | |||
+ | * Enter a name - Temperature Detection Stopped | ||
+ | * Use the dropdown box next to Triggering event to select Device Events | ||
+ | * Use the dropdown box to select TemperatureEnd | ||
+ | * Click Select to select which devices for use with the alarm | ||
+ | ** Select the Thermal camera in the list, click Add | ||
+ | ** Repeat the process for the 2nd channel of the camera | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_40.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_40.jpg|800px]] | ||
+ | |||
+ | Both Alarms created | ||
+ | |||
+ | Temperature Detection Started | ||
+ | Temperature Detection Stopped | ||
[[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_41.jpg|800px]] | [[File:Temperature_Monitoring_-_Milestone_-_Configure_Milestone_-_41.jpg|800px]] |
Latest revision as of 22:58, 15 May 2020
Contents
Add Camera To Milestone and Configure Alarm Event
Description
This guide will show how to add the camera to the Milestone server and configure the alarm event for Temperature Monitoring
Prerequisites
- Milestone Corporate 2019 R3, device pack 10.8a
Step by Step Instructions
Add device in Milestone XProtect Management Client
1. Add Device to Recording Server by left clicking Recording Servers
Right click the server
Select Add Hardware
2. Select Manual Add
Click Next
3. Click Add
Enter the username and password for the camera
Click Next
4. Select ONVIF for device driver
Click Next
5. Enter the IP address of the camera
Select (Auto-detect)
Click Next
The software will automatically detect the camera
Click Next
Click Next
6. Check the box to enable all Hardware for the camera
Click Next
Click Finish
The camera will appear in the list
Add event in Milestone XProtect Management Client
1. Select Cameras
Then left click to select the Thermal camera in the list
Click the Events tab
2. Click Add to create a new Event
3. Find and select Temperature Detection Started in the list
Click OK
4. Repeat the process again to create a new Event
- Click Add
- Select Temperature Detection Stopped
- Click OK
5. Left click to select the 2nd channel of the Thermal camera
Repeat the previous steps on the 2nd channel to configure both events
Temperature Detection Started / Temperature Detection Stopped Event configured on 2nd channel:
Add rules for event
1. Select Rules
Right click Rules
Select Add Rule
2. Enter a name for the Rule
Click event
3. Select Devices > Configurable Events
Find Temperature Detection Started in the list and click to select
Click OK
4. Click devices/recording/server/managementserver
5. Left click to select the Thermal camera in the list
Click Add
6. Repeat the process for the 2nd channel
Click OK
7. Click Next
8. Configure the schedule for the event
In this example we select All days by clicking Day of week is then selecting all Days
9. Click Next
10. Select action to perform when the event is triggered
In this example we select
- Record - Start recording on <devices>
- Log - Make new <log entry>
Click logentry
11. Click to add each type of System Information to the log template
Click OK
Click Next
12. Select Perform stop action on <event>
Click Next
13. Click Finish
Alarm configuration
1. Select Alarm Definitions
Right click Alarm Definitions
Select Add New
2. Check to Enable
Enter a name - Temperature Detection Start
3. Use the dropdown box next to Triggering event to select Device Events
Use the dropdown box to select TemperatureStart
4. Click Select to select which devices for use with the alarm
5. Select the Thermal camera in the list, click Add
6. Repeat the process for the 2nd channel of the camera
Click OK
7. Click Save
8. Another rule must be created for the event end
Right click Alarm Definitions
Select Add New
9. Click to Enable
- Enter a name - Temperature Detection Stopped
- Use the dropdown box next to Triggering event to select Device Events
- Use the dropdown box to select TemperatureEnd
- Click Select to select which devices for use with the alarm
- Select the Thermal camera in the list, click Add
- Repeat the process for the 2nd channel of the camera
Both Alarms created
Temperature Detection Started Temperature Detection Stopped