Notice: Firmware Links Under Maintenance We are currently undergoing maintenance on all firmware links. If any links are inaccessible, please email or contact Tech Support for the firmware. We appreciate your patience during the maintenance, thank you for your understanding.
Difference between revisions of "Thermal/DHI-ASI7213X-T1/Instructions/Alarm Input and Output"
(→Normal Body Temperature Indication Light) |
|||
(34 intermediate revisions by 3 users not shown) | |||
Line 16: | Line 16: | ||
==Cable Connections== | ==Cable Connections== | ||
− | *Alarm1 = | + | *Alarm1 = High Temp |
− | *Alarm2 = | + | *Alarm2 = Normal Temp or No Mask |
− | *No alert for | + | *No alert for face detection currently. |
===Contact 1=== | ===Contact 1=== | ||
Line 138: | Line 138: | ||
|- | |- | ||
|rowspan="9"|CON3 | |rowspan="9"|CON3 | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
|- | |- | ||
|Black and blue | |Black and blue | ||
Line 179: | Line 169: | ||
|Lock control normally closed port. | |Lock control normally closed port. | ||
|} | |} | ||
− | == | + | |
− | [[File: | + | ==Alarm Outputs 1 and 2 - New Firmware== |
+ | |||
+ | {| class="wikitable" | ||
+ | |- | ||
+ | !|PLEASE NOTE: These instructions are for Alarm Outputs 1 and 2 on firmware version 1.000.10BE001.0.R.200722 and later | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | ===High Body Temperature Indication Light=== | ||
+ | [[File:High Temp Alarm Setup-newfw.png|700px|right]] | ||
{| class="wikitable" | {| class="wikitable" | ||
!|Port | !|Port | ||
Line 202: | Line 201: | ||
|- | |- | ||
|} | |} | ||
− | < | + | <br><br><br><br><br><br><br><br><br><br><br><br><br><br> |
+ | |||
+ | ===Normal Body Temperature or No Mask Indication Light=== | ||
+ | {| class="wikitable" | ||
+ | |- | ||
+ | !|PLEASE NOTE: On firmware version 1.000.10BE001.0.R.200722 and later, you must set the Alarm Output 2 mode setting to either "Normal Temperature Alarm" for being triggered when a normal temperature is detected or "No Mask Alarm" for being triggered when no mask is detected | ||
+ | |- | ||
+ | |[[File:ThermalKioskAlarmOutput2.PNG|600px|center]] | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | [[File:Normal Temp alarm Setup-newfw.png|700px|right]] | ||
+ | {| class="wikitable" | ||
+ | !|Port | ||
+ | !colspan="2"|Cable Color | ||
+ | !|Cable Name | ||
+ | !|Description | ||
+ | |- | ||
+ | |+CON2 | ||
+ | |- | ||
+ | |rowspan="9"|CON2 | ||
+ | |- | ||
+ | |White and blue | ||
+ | |[[File:Wire_white_blue_stripe.svg|35px]] | ||
+ | |ALARM2_NO | ||
+ | |Alarm 2 normally open output port. | ||
+ | |- | ||
+ | |White and gray | ||
+ | |[[File:Wire_white_gray_stripe.svg|35px]] | ||
+ | |ALARM2_COM | ||
+ | |Alarm 2 common output port. | ||
+ | |} | ||
+ | <br><br><br><br><br><br><br><br><br><br><br><br><br><br> | ||
+ | |||
+ | ==Alarm Outputs 1 and 2 - Old Firmware== | ||
+ | {| class="wikitable" | ||
+ | |- | ||
+ | !|PLEASE NOTE: These instructions are for Alarm Outputs 1 and 2 on firmware older than version 1.000.10BE001.0.R.200722 | ||
+ | |- | ||
+ | |} | ||
− | ==High Body Temperature Indication Light== | + | ===High Body Temperature Indication Light=== |
+ | [[File:High Temp Alarm Setup.png |700px|right]] | ||
{| class="wikitable" | {| class="wikitable" | ||
!|Port | !|Port | ||
Line 226: | Line 265: | ||
|} | |} | ||
<embedvideo service="youtube">https://youtu.be/5gC_ptUkYD8</embedvideo> | <embedvideo service="youtube">https://youtu.be/5gC_ptUkYD8</embedvideo> | ||
+ | |||
+ | ===Normal Body Temperature Indication Light=== | ||
+ | [[File:Normal Temp alarm Setup.png|700px|right]] | ||
+ | {| class="wikitable" | ||
+ | !|Port | ||
+ | !colspan="2"|Cable Color | ||
+ | !|Cable Name | ||
+ | !|Description | ||
+ | |- | ||
+ | |+CON2 | ||
+ | |- | ||
+ | |rowspan="9"|CON2 | ||
+ | |- | ||
+ | |White and red | ||
+ | |[[File:Wire_white_red_stripe.svg|35px]] | ||
+ | |ALARM1_NO | ||
+ | |Alarm 1 normally open output port | ||
+ | |- | ||
+ | |White and orange | ||
+ | |[[File:Wire_white_orange_stripe.svg|35px]] | ||
+ | |ALARM1_COM | ||
+ | |Alarm 1 common output port. | ||
+ | |- | ||
+ | |} | ||
+ | <embedvideo service="youtube">https://youtu.be/5toY3dhp2fI</embedvideo> | ||
+ | |||
==Door Strike Physical Setup== | ==Door Strike Physical Setup== | ||
+ | [[File:Door Strike Physical Setup.png|700px|right]] | ||
{| class="wikitable" | {| class="wikitable" | ||
!|Port | !|Port | ||
Line 248: | Line 314: | ||
|} | |} | ||
<embedvideo service="youtube">https://youtu.be/dGHAkGemMjs</embedvideo> | <embedvideo service="youtube">https://youtu.be/dGHAkGemMjs</embedvideo> | ||
+ | |||
==Door Release Button Physical Setup== | ==Door Release Button Physical Setup== | ||
+ | |||
+ | [[File:Door Release Button Physical Setup.png|700px|right]] | ||
{| class="wikitable" | {| class="wikitable" | ||
!|Port | !|Port | ||
Line 271: | Line 340: | ||
|} | |} | ||
<embedvideo service="youtube">https://youtu.be/dGHAkGemMjs</embedvideo> | <embedvideo service="youtube">https://youtu.be/dGHAkGemMjs</embedvideo> | ||
+ | |||
==Card Reader:RS485== | ==Card Reader:RS485== | ||
{| class="wikitable" | {| class="wikitable" | ||
Line 296: | Line 366: | ||
*Once the security module is enabled, the exit button, lock control and firefighting linkage will be invalid | *Once the security module is enabled, the exit button, lock control and firefighting linkage will be invalid | ||
|} | |} | ||
+ | <gallery> | ||
+ | file:DHI-ASI7213X-T1_Door_Config_DSS-Express.png|Door Config in DSS Express | ||
+ | </gallery> | ||
+ | |||
==Card Reader:Wiegand== | ==Card Reader:Wiegand== | ||
{| class="wikitable" | {| class="wikitable" | ||
Line 323: | Line 397: | ||
==SystemUI Set Temperature Threshold== | ==SystemUI Set Temperature Threshold== | ||
<embedvideo service="youtube">https://youtu.be/ZjVNCdwMB0I</embedvideo> | <embedvideo service="youtube">https://youtu.be/ZjVNCdwMB0I</embedvideo> | ||
+ | |||
+ | ==Notes== | ||
+ | *Access Link Enable is only used when a door is configured for access for normal temperature. If the Kiosk is only used for LED lights, this option shouldn't be enabled. |
Latest revision as of 15:44, 9 July 2021
Contents
- 1 Alarm Input and Output
- 1.1 Web Interface
- 1.2 Cable Connections
- 1.3 Alarm Outputs 1 and 2 - New Firmware
- 1.4 Alarm Outputs 1 and 2 - Old Firmware
- 1.5 Door Strike Physical Setup
- 1.6 Door Release Button Physical Setup
- 1.7 Card Reader:RS485
- 1.8 Card Reader:Wiegand
- 1.9 WebUI Alarm Setup
- 1.10 SystemUI Set Temperature Threshold
- 1.11 Notes
Alarm Input and Output
Web Interface
Cable Connections
- Alarm1 = High Temp
- Alarm2 = Normal Temp or No Mask
- No alert for face detection currently.
Contact 1
Contact 2
Contact 3
Alarm Outputs 1 and 2 - New Firmware
PLEASE NOTE: These instructions are for Alarm Outputs 1 and 2 on firmware version 1.000.10BE001.0.R.200722 and later |
---|
High Body Temperature Indication Light
Port | Cable Color | Cable Name | Description | |
---|---|---|---|---|
CON2 | ||||
White and red | ![]() |
ALARM1_NO | Alarm 1 normally open output port | |
White and orange | ![]() |
ALARM1_COM | Alarm 1 common output port. |
Normal Body Temperature or No Mask Indication Light
PLEASE NOTE: On firmware version 1.000.10BE001.0.R.200722 and later, you must set the Alarm Output 2 mode setting to either "Normal Temperature Alarm" for being triggered when a normal temperature is detected or "No Mask Alarm" for being triggered when no mask is detected |
---|
Port | Cable Color | Cable Name | Description | |
---|---|---|---|---|
CON2 | ||||
White and blue | ![]() |
ALARM2_NO | Alarm 2 normally open output port. | |
White and gray | ![]() |
ALARM2_COM | Alarm 2 common output port. |
Alarm Outputs 1 and 2 - Old Firmware
PLEASE NOTE: These instructions are for Alarm Outputs 1 and 2 on firmware older than version 1.000.10BE001.0.R.200722 |
---|
High Body Temperature Indication Light
Port | Cable Color | Cable Name | Description | |
---|---|---|---|---|
CON2 | ||||
White and blue | ![]() |
ALARM2_NO | Alarm 2 normally open output port. | |
White and gray | ![]() |
ALARM2_COM | Alarm 2 common output port. |
Normal Body Temperature Indication Light
Port | Cable Color | Cable Name | Description | |
---|---|---|---|---|
CON2 | ||||
White and red | ![]() |
ALARM1_NO | Alarm 1 normally open output port | |
White and orange | ![]() |
ALARM1_COM | Alarm 1 common output port. |
Door Strike Physical Setup
Port | Cable Color | Cable Name | Description | |
---|---|---|---|---|
CON3 | ||||
Black and brown | ![]() |
DOOR1_COM | Lock control common port. | |
Black and purple | ![]() |
DOOR1_NC | Lock control normally closed port. |
Door Release Button Physical Setup
Port | Cable Color | Cable Name | Description | |
---|---|---|---|---|
CON3 | ||||
Black and blue | ![]() |
GND | Connected to the common GND port. | |
Black and green | ![]() |
PUSH1 | Door open button of door No.1 |
Card Reader:RS485
Card Reader:Wiegand
WebUI Alarm Setup
SystemUI Set Temperature Threshold
Notes
- Access Link Enable is only used when a door is configured for access for normal temperature. If the Kiosk is only used for LED lights, this option shouldn't be enabled.