Notice: Firmware Links Under Maintenance We are currently undergoing maintenance on all firmware links. If any links are inaccessible, please email or contact Tech Support for the firmware. We appreciate your patience during the maintenance, thank you for your understanding.
Difference between revisions of "Thermal/DHI-ASI7213X-T1/Instructions/Alarm Input and Output"
(→Alarm Outputs 1 and 2 - New Firmware) |
|||
(14 intermediate revisions by 2 users not shown) | |||
Line 17: | Line 17: | ||
==Cable Connections== | ==Cable Connections== | ||
*Alarm1 = High Temp | *Alarm1 = High Temp | ||
− | *Alarm2 = No Mask | + | *Alarm2 = Normal Temp or No Mask |
*No alert for face detection currently. | *No alert for face detection currently. | ||
Line 179: | Line 179: | ||
===High Body Temperature Indication Light=== | ===High Body Temperature Indication Light=== | ||
− | [[File: | + | [[File:High Temp Alarm Setup-newfw.png|700px|right]] |
{| class="wikitable" | {| class="wikitable" | ||
!|Port | !|Port | ||
Line 201: | Line 201: | ||
|- | |- | ||
|} | |} | ||
− | <br><br><br><br><br><br><br><br><br><br><br><br><br><br> | + | <br><br><br><br><br><br><br><br><br><br><br><br><br><br> |
+ | |||
+ | ===Normal Body Temperature or No Mask Indication Light=== | ||
+ | {| class="wikitable" | ||
+ | |- | ||
+ | !|PLEASE NOTE: On firmware version 1.000.10BE001.0.R.200722 and later, you must set the Alarm Output 2 mode setting to either "Normal Temperature Alarm" for being triggered when a normal temperature is detected or "No Mask Alarm" for being triggered when no mask is detected | ||
+ | |- | ||
+ | |[[File:ThermalKioskAlarmOutput2.PNG|600px|center]] | ||
+ | |- | ||
+ | |} | ||
− | + | [[File:Normal Temp alarm Setup-newfw.png|700px|right]] | |
− | [[File: | ||
{| class="wikitable" | {| class="wikitable" | ||
!|Port | !|Port | ||
Line 225: | Line 233: | ||
|Alarm 2 common output port. | |Alarm 2 common output port. | ||
|} | |} | ||
− | + | <br><br><br><br><br><br><br><br><br><br><br><br><br><br> | |
==Alarm Outputs 1 and 2 - Old Firmware== | ==Alarm Outputs 1 and 2 - Old Firmware== | ||
Line 389: | Line 397: | ||
==SystemUI Set Temperature Threshold== | ==SystemUI Set Temperature Threshold== | ||
<embedvideo service="youtube">https://youtu.be/ZjVNCdwMB0I</embedvideo> | <embedvideo service="youtube">https://youtu.be/ZjVNCdwMB0I</embedvideo> | ||
+ | |||
+ | ==Notes== | ||
+ | *Access Link Enable is only used when a door is configured for access for normal temperature. If the Kiosk is only used for LED lights, this option shouldn't be enabled. |
Latest revision as of 15:44, 9 July 2021
Contents
- 1 Alarm Input and Output
- 1.1 Web Interface
- 1.2 Cable Connections
- 1.3 Alarm Outputs 1 and 2 - New Firmware
- 1.4 Alarm Outputs 1 and 2 - Old Firmware
- 1.5 Door Strike Physical Setup
- 1.6 Door Release Button Physical Setup
- 1.7 Card Reader:RS485
- 1.8 Card Reader:Wiegand
- 1.9 WebUI Alarm Setup
- 1.10 SystemUI Set Temperature Threshold
- 1.11 Notes
Alarm Input and Output
Web Interface
Cable Connections
- Alarm1 = High Temp
- Alarm2 = Normal Temp or No Mask
- No alert for face detection currently.
Contact 1
Contact 2
Contact 3
Alarm Outputs 1 and 2 - New Firmware
PLEASE NOTE: These instructions are for Alarm Outputs 1 and 2 on firmware version 1.000.10BE001.0.R.200722 and later |
---|
High Body Temperature Indication Light
Port | Cable Color | Cable Name | Description | |
---|---|---|---|---|
CON2 | ||||
White and red | ![]() |
ALARM1_NO | Alarm 1 normally open output port | |
White and orange | ![]() |
ALARM1_COM | Alarm 1 common output port. |
Normal Body Temperature or No Mask Indication Light
PLEASE NOTE: On firmware version 1.000.10BE001.0.R.200722 and later, you must set the Alarm Output 2 mode setting to either "Normal Temperature Alarm" for being triggered when a normal temperature is detected or "No Mask Alarm" for being triggered when no mask is detected |
---|
Port | Cable Color | Cable Name | Description | |
---|---|---|---|---|
CON2 | ||||
White and blue | ![]() |
ALARM2_NO | Alarm 2 normally open output port. | |
White and gray | ![]() |
ALARM2_COM | Alarm 2 common output port. |
Alarm Outputs 1 and 2 - Old Firmware
PLEASE NOTE: These instructions are for Alarm Outputs 1 and 2 on firmware older than version 1.000.10BE001.0.R.200722 |
---|
High Body Temperature Indication Light
Port | Cable Color | Cable Name | Description | |
---|---|---|---|---|
CON2 | ||||
White and blue | ![]() |
ALARM2_NO | Alarm 2 normally open output port. | |
White and gray | ![]() |
ALARM2_COM | Alarm 2 common output port. |
Normal Body Temperature Indication Light
Port | Cable Color | Cable Name | Description | |
---|---|---|---|---|
CON2 | ||||
White and red | ![]() |
ALARM1_NO | Alarm 1 normally open output port | |
White and orange | ![]() |
ALARM1_COM | Alarm 1 common output port. |
Door Strike Physical Setup
Port | Cable Color | Cable Name | Description | |
---|---|---|---|---|
CON3 | ||||
Black and brown | ![]() |
DOOR1_COM | Lock control common port. | |
Black and purple | ![]() |
DOOR1_NC | Lock control normally closed port. |
Door Release Button Physical Setup
Port | Cable Color | Cable Name | Description | |
---|---|---|---|---|
CON3 | ||||
Black and blue | ![]() |
GND | Connected to the common GND port. | |
Black and green | ![]() |
PUSH1 | Door open button of door No.1 |
Card Reader:RS485
Card Reader:Wiegand
WebUI Alarm Setup
SystemUI Set Temperature Threshold
Notes
- Access Link Enable is only used when a door is configured for access for normal temperature. If the Kiosk is only used for LED lights, this option shouldn't be enabled.