Difference between revisions of "Template:Tripwire SystemUI NewGUI"

 
(13 intermediate revisions by the same user not shown)
Line 1: Line 1:
  
−
=Step By Step Instructions=
+
===Video Instructions===
−
1. From the Main Menu select "AI"
+
<embedvideo service="youtube">https://youtu.be/S4MUxjh54Uc</embedvideo>
  
−
[[File:IVSTripwireSytemUINew1.png|500px]]
+
===Step by Step Instructions===
 +
1. From the Main Menu select '''AI'''
 +
 
 +
[[File:How_To_Setup_Intrusion_-_NewUI_-_1.jpg|500px]]
 +
 
 +
2. Select '''Parameters''' on the left.
 +
 
 +
Select '''Smart Plan'''.
 +
 
 +
[[File:How_To_Setup_Intrusion_-_NewUI_-_2.jpg|500px]]
 +
 
 +
3. Use the drop down box to select the Channel
  
 
[[File:How_To_Setup_Intrusion_-_NewUI_-_3.jpg|500px]]
 
[[File:How_To_Setup_Intrusion_-_NewUI_-_3.jpg|500px]]
  
−
2. Select "Parameters" on the left.
+
4. Click and highlight '''IVS''' (You may need to de-select any other options).
−
Then select "Smart Plan".
+
 
−
Select the camera channel at the top.
+
[[File:How_To_Setup_Intrusion_-_NewUI_-_4.jpg|500px]]
−
Select and highlight "IVS" (You may need to de-select any other options).
+
 
−
Select "Apply"
+
The icon will highlight when selected.
 +
 
 +
Click '''Apply'''
 +
 
 +
[[File:How_To_Setup_Intrusion_-_NewUI_-_5.jpg|500px]]
 +
 
 +
5. Click Parameters > IVS
 +
 
 +
[[File:How_To_Setup_Intrusion_-_NewUI_-_6.jpg|500px]]
 +
 
 +
6. Use the drop-down box to select the Channel
 +
 
 +
Then click Add in the lower right side of the screen to Add an IVS rule
 +
 
 +
[[File:How_To_Setup_Intrusion_-_NewUI_-_7.jpg|500px]]
 +
 
 +
7. The created rule will appear in the list
 +
 
 +
[[File:How_To_Setup_Intrusion_-_NewUI_-_8.jpg|500px]]
 +
 
 +
 
 +
 
 +
9. Click the Pencil icon to draw the Tripwire rule
 +
 
 +
[[File:Tripwire_Setup_-_NewGUI_-_9.jpg|500px]]
 +
 
 +
10. The Channel will fullscreen.
 +
 
 +
Left click anywhere inside the video frame to begin drawing the Trip line, then use the mouse to draw the trip line.
 +
 
 +
Right click to end drawing
 +
 
 +
[[File:Tripwire_Setup_-_NewGUI_-_10.jpg|500px]]
 +
 
 +
[[File:Tripwire_Setup_-_NewGUI_-_11.jpg|500px]]
  
−
IVSTripwireSytemUINew2.png
+
11. The Tripwire menu will appear
  
−
3. Select "IVS" on the left.
+
[[File:Tripwire_Setup_-_NewGUI_-_12.jpg|500px]]
−
Then choose the channel number at the top and if the IVS will be done by the camera or by the recorder, by selecting either "AI by Camera" or "AI by Device" next to the channel number.
 
−
Select "Add" at the bottom to create a new IVS alarm rule.
 
−
Click on the drop-down menu under "Type" for the new rule you created and change set it to "Tripwire".
 
−
Select the Pencil icon under "Draw"
 
  
−
IVSTripwireSytemUINew3.png
+
*Name: A name can be applied to the rule
 +
*Direction: Both, A To B, B To A
  
−
4. Left click anywhere on the camera view to start the tripwire line.
+
Click [[File:Tripwire_Setup_-_NewGUI_-_Target_Filter.jpg]] icon to set the Target Filter (maximum and minimum size size for Objects to follow rule)
−
Left click anywhere else on the camera view to complete the segment of the line. Continue moving your mouse and left clicking to continue making multiple segments of the tripwire line.
 
−
When done drawing the line segments, right click to finish the line.
 
−
Give this rule a name by selecting the text box next to "Name" and typing in a name.
 
−
Select the drop-down menu next to "Direction" to choose if the IVS alarm is triggered in both directions ("Both") or just one direction ("A To B" or "B To A").
 
−
When you are done configuring the Tripwire rules, select "OK"
 
  
−
IVSTripwireSytemUINew4.png
+
Click [[File:Tripwire_Setup_-_NewGUI_-_Trash_Icon.jpg]] icon to clear the current rule
  
−
6. Select the Gear icon under "Trigger" to configure what happens when the tripwire alarm is triggered:
+
Once the tripwire rule settings have been created click OK
−
Period - Sets the time and days of the week this alarm can be triggered
 
−
Alarm Out - Sets alarm outputs that will be activate when this alarm is triggered
 
−
Latch - Sets how long the alarm outputs will stay activated when the alarm is triggered
 
−
Send Email - Sends an email, via the settings set in the Email section of the Network settings on the recorder, when the alarm is triggered
 
−
Record Channel - Sets which channels are recorded when the alarm is triggered
 
−
PTZ Activation - Sets the behavior of a PTZ camera connected to the same recorder when the alarm is triggered
 
−
Post-Record - Sets the amount of seconds that are recorded after the alarm event is done being triggered, if "Record Channel" is enabled
 
−
Tour - Enables a tour when the alarm is triggered
 
−
Buzzer - Makes the recorder emit an audible beeping noise when the alarm is triggered
 
−
Log - Records the event information in the system log when the alarm is triggerd
 
  
−
Select "Apply" to save the settings
+
12. Click the [[File:Tripwire_Setup_-_NewGUI_-_Trigger.jpg]] icon to set the Trigger settings when the IVS Tripwire rule is engaged.
  
−
IVSTripwireSytemUINew5.png
+
[[File:Tripwire_Setup_-_NewGUI_-_13.jpg|500px]]
  
−
7. Select "Apply" to save the Tripwire IVS alarm settings
+
[[Alarm_Config_Settings|> Configure Tripwire Response]]
  
−
IVSTripwireSytemUINew6.png
+
Click '''Apply''' to save the settings

Latest revision as of 17:55, 29 October 2020

Video Instructions

Step by Step Instructions

1. From the Main Menu select AI

How To Setup Intrusion - NewUI - 1.jpg

2. Select Parameters on the left.

Select Smart Plan.

How To Setup Intrusion - NewUI - 2.jpg

3. Use the drop down box to select the Channel

How To Setup Intrusion - NewUI - 3.jpg

4. Click and highlight IVS (You may need to de-select any other options).

How To Setup Intrusion - NewUI - 4.jpg

The icon will highlight when selected.

Click Apply

How To Setup Intrusion - NewUI - 5.jpg

5. Click Parameters > IVS

How To Setup Intrusion - NewUI - 6.jpg

6. Use the drop-down box to select the Channel

Then click Add in the lower right side of the screen to Add an IVS rule

How To Setup Intrusion - NewUI - 7.jpg

7. The created rule will appear in the list

How To Setup Intrusion - NewUI - 8.jpg


9. Click the Pencil icon to draw the Tripwire rule

Tripwire Setup - NewGUI - 9.jpg

10. The Channel will fullscreen.

Left click anywhere inside the video frame to begin drawing the Trip line, then use the mouse to draw the trip line.

Right click to end drawing

Tripwire Setup - NewGUI - 10.jpg

Tripwire Setup - NewGUI - 11.jpg

11. The Tripwire menu will appear

Tripwire Setup - NewGUI - 12.jpg

  • Name: A name can be applied to the rule
  • Direction: Both, A To B, B To A

Click Tripwire Setup - NewGUI - Target Filter.jpg icon to set the Target Filter (maximum and minimum size size for Objects to follow rule)

Click Tripwire Setup - NewGUI - Trash Icon.jpg icon to clear the current rule

Once the tripwire rule settings have been created click OK

12. Click the Tripwire Setup - NewGUI - Trigger.jpg icon to set the Trigger settings when the IVS Tripwire rule is engaged.

Tripwire Setup - NewGUI - 13.jpg

> Configure Tripwire Response

Click Apply to save the settings

Retrieved from "https://DahuaWiki.com/index.php?title=Template:Tripwire_SystemUI_NewGUI&oldid=68853"