Difference between revisions of "Template:LPR Camera Guide Setup"
| (3 intermediate revisions by the same user not shown) | |||
| Line 68: | Line 68: | ||
A sample Identification Area and Snap Line will be displayed. | A sample Identification Area and Snap Line will be displayed. | ||
| − | To clear or Redraw these Click either Iden Area [[File:iden_area.jpg|100px] or Snap Line [[File:snap_line.jpg|100px]] | + | To clear or Redraw these Click either '''Iden Area''' [[File:iden_area.jpg|100px]] or '''Snap Line''' [[File:snap_line.jpg|100px]] |
| − | '''Then''' click [[File:redraw.jpg|100px]] | + | '''Then''' click '''Redraw''' - [[File:redraw.jpg|100px]] |
To create new Recognition settings: | To create new Recognition settings: | ||
| − | * Click Iden Area. [[File:iden_area.jpg|100px]] | + | * Click '''Iden Area.''' [[File:iden_area.jpg|100px]] |
Click and draw 4 lines on the video frame to create a recognition area. Only plates in this area will be detected. | Click and draw 4 lines on the video frame to create a recognition area. Only plates in this area will be detected. | ||
| − | * Click Snap Line. [[File:snap_line.jpg|100px]] | + | * Click '''Snap Line'''. [[File:snap_line.jpg|100px]] |
Draw snap line by dragging mouse on the area. The snap line must cross the area. Vehicles passing this line will trigger plate detection. | Draw snap line by dragging mouse on the area. The snap line must cross the area. Vehicles passing this line will trigger plate detection. | ||
| − | 3) Click Save to complete the Setup. | + | [[File:LPR_Camera_Recognition_Setup.jpg]] |
| + | |||
| + | 3) Click '''Save''' to complete the Setup. | ||
Click Finish, exit Guide interface and enter Live interface. | Click Finish, exit Guide interface and enter Live interface. | ||
| + | |||
| + | |||
| + | |||
| + | Example at Live interface: | ||
| + | |||
| + | [[File:LPR_example_1.png]] | ||
| + | |||
| + | [[File:LPR_example_2.png]] | ||
| + | |||
| + | * Make sure the vehicle is within the red identification area line | ||
| + | * The green snap line is about 1/3 of the road | ||
| + | * Angle between the bottom of the license plate and the screen ≤5° | ||
| + | * The license plate has more than 140 pixels. | ||
Latest revision as of 23:09, 28 May 2021
The Guide interface is useful to configure the correct settings for license plate capture
Log into the Web UI of the camera by typing the IP into a web browser.
Enter the username/password and click Login
- Click the Guide tab.
On the Guide interface, you can configure capture scenarios. You can click at at the upper-right corner of Guide interface to exit at anytime.
1. Confirmation
- Confirm the Software Version is the latest (Visit the Product page for latest firmware version - Link), and then click OK.
2. Plate Pixel
- You can check whether the video image is properly zoomed and focused by checking the plate pixel.
Below the video frame there is an example of the optimal plate positioning:
Use the Pixel Plate settings to adjust the camera for zoom and focus
- Drag the Zoom and Focus bar to adjust the image properly
- Position a vehicle/plate into the camera's view
Click Snapshot to take a snapshot of the plate (Snapshot button will become Resume)
- Drag the yellow box to the position of the plate
- Click Local Range to zoom the picture by 2x or 4x zoom rate (if required)
- Continue to adjust the position yellow box to make it optimal plate size:
If the plate within the yellow box is larger than the optimal plate size in the example, zoom out the video image; if smaller, zoom in the video image.
It may also require reviewing proper mounting requirements/positions if any softw3are adjustments do not allow for optimal plate positioning.
- Once the plate is in optimal position, click Check Pixel. Click Yes to confirm.
3. Recognition
- This section will configure the recognition/identification area for detection of license plates. The sample image can be used as a reference
A sample Identification Area and Snap Line will be displayed.
To clear or Redraw these Click either Iden Area 
or Snap Line 
Then click Redraw - 
To create new Recognition settings:
- Click Iden Area.
Click and draw 4 lines on the video frame to create a recognition area. Only plates in this area will be detected.
- Click Snap Line.
Draw snap line by dragging mouse on the area. The snap line must cross the area. Vehicles passing this line will trigger plate detection.
3) Click Save to complete the Setup.
Click Finish, exit Guide interface and enter Live interface.
Example at Live interface:
- Make sure the vehicle is within the red identification area line
- The green snap line is about 1/3 of the road
- Angle between the bottom of the license plate and the screen ≤5°
- The license plate has more than 140 pixels.
