Difference between revisions of "CMS/DSS/Server Main-Sub"

(Created page with "==Descriptions== DSS All-in-one supports Main-sub Mode which allows you to create a DSS Cluster. Compared to a single DSS All-in-one, Main-sub mode is better in terms of Devic...")
 
(Step by Step Instructions)
 
(One intermediate revision by the same user not shown)
Line 10: Line 10:
 
=Step by Step Instructions=
 
=Step by Step Instructions=
  
 +
'''Step 0: Check DSS Version'''
  
[[File:DSSDBK01.jpg|750px]]
+
Log into DSS Web Config Page of the Sub Server and click on About
 +
 
 +
[[File:7016Mainsub01.jpg|750px]]
 +
 
 +
Make sure that all your DSS All-in-ones are of the same version.
 +
 
 +
'''Step 1: Decide which one is the Main Server and which is (are) Sub Server (s)'''
 +
 
 +
In Main-sub Mode, you could only have [[one Main Server]], and the other(s) will be Sub Servers. Sub-servers will register themselves onto the Main Server so that their resources can be deployed.
 +
 
 +
For example, I have two DSS All-in-ones, whose IP addresses are 10.5.2.60 and 10.5.2.65. I will nominate 10.5.2.60 as the Main Server and 10.5.2.65 as the Sub Server.
 +
 
 +
'''Step 2: Configure Sub Server(s)'''
 +
 
 +
Log into DSS Web Config Page of the Sub Server.
 +
 
 +
2-1. On the homepage, select “Sub Server”, which will make this DSS work as a Sub Server.
 +
 
 +
2-2. Then, insert the Main Server IP and the HTTPS Port (443 by default).
 +
 
 +
2-3. In the end, click on Apply and Restart.
 +
 
 +
[[File:7016Mainsub02.jpg|750px]]
 +
 
 +
'''Step 3: Configure Sub-server on the Main Server.'''
 +
 
 +
3-1. Log into DSS Client with the Main Server IP and select [System Deployment]
 +
 
 +
[[File:7016Mainsub03.jpg|750px]]
 +
 
 +
3-2. Here you can see all the Sub-servers that registered themselves on the Main Server.
 +
 
 +
You can enable or disable any of the Sub Servers.
 +
 
 +
[[File:7016Mainsub04.jpg|750px]]
 +
 
 +
'''Step 4: Allocate resources'''
 +
 
 +
4-1. Click on [Allocate Resources] and you can assign devices to Sub Servers.
 +
 
 +
[[File:7016Mainsub05.jpg|750px]]
 +
 
 +
4-2. You can drag the Devices to any of the Sub Servers you want.
 +
 
 +
[[File:7016Mainsub06.jpg|750px]]
 +
 
 +
4-3. Here is an example after resources are allocated
 +
 
 +
[[File:7016Mainsub07.jpg|750px]]
 +
 
 +
4-4. When adding a Device, you can also assign the Device to any of the Servers in the cluster.
 +
 
 +
[[File:7016Mainsub08.jpg|750px]]

Latest revision as of 06:27, 21 December 2022

Descriptions

DSS All-in-one supports Main-sub Mode which allows you to create a DSS Cluster. Compared to a single DSS All-in-one, Main-sub mode is better in terms of Device Access Capability, Bandwidth, and System Redundancy, etc.

This document will walk you through the process of configuring DSS Main-sub Mode.

Prerequisites

Step by Step Instructions

Step 0: Check DSS Version

Log into DSS Web Config Page of the Sub Server and click on About

7016Mainsub01.jpg

Make sure that all your DSS All-in-ones are of the same version.

Step 1: Decide which one is the Main Server and which is (are) Sub Server (s)

In Main-sub Mode, you could only have one Main Server, and the other(s) will be Sub Servers. Sub-servers will register themselves onto the Main Server so that their resources can be deployed.

For example, I have two DSS All-in-ones, whose IP addresses are 10.5.2.60 and 10.5.2.65. I will nominate 10.5.2.60 as the Main Server and 10.5.2.65 as the Sub Server.

Step 2: Configure Sub Server(s)

Log into DSS Web Config Page of the Sub Server.

2-1. On the homepage, select “Sub Server”, which will make this DSS work as a Sub Server.

2-2. Then, insert the Main Server IP and the HTTPS Port (443 by default).

2-3. In the end, click on Apply and Restart.

7016Mainsub02.jpg

Step 3: Configure Sub-server on the Main Server.

3-1. Log into DSS Client with the Main Server IP and select [System Deployment]

7016Mainsub03.jpg

3-2. Here you can see all the Sub-servers that registered themselves on the Main Server.

You can enable or disable any of the Sub Servers.

7016Mainsub04.jpg

Step 4: Allocate resources

4-1. Click on [Allocate Resources] and you can assign devices to Sub Servers.

7016Mainsub05.jpg

4-2. You can drag the Devices to any of the Sub Servers you want.

7016Mainsub06.jpg

4-3. Here is an example after resources are allocated

7016Mainsub07.jpg

4-4. When adding a Device, you can also assign the Device to any of the Servers in the cluster.

7016Mainsub08.jpg