Difference between revisions of "NVR/Basic Setup/Initial Setup"

Line 1: Line 1:
 
File:Standalone_DVR_Quick_Start_Guide_V1.0.0.pdf
 
File:Standalone_DVR_Quick_Start_Guide_V1.0.0.pdf
 +
 
===Boot up and Shutdown===
 
===Boot up and Shutdown===
 
====Boot up====
 
====Boot up====
 
Before the boot up, please make sure:
 
Before the boot up, please make sure:
*For device security, please connect the NVR to the power adapter first and then connect the device to the power socket.  
+
 
*The rated input voltage matches the device power on-off button. Please make sure the power wire connection is OK. Then click the power on-off button.  
+
* For device security, please connect the NVR to the power adapter first and then connect the device to the power socket.
*Always use the stable current, if necessary UPS is a best alternative measure.
+
* The rated input voltage matches the device power on-off button. Please make sure the power wire connection is OK. Then click the power on-off button.
Please follow the steps listed below to boot up the device.  
+
* Always use the stable current, if necessary UPS is a best alternative measure.
*Connect the device to the monitor and then connect a mouse.
+
 
*Connect power cable.
+
Please follow the steps listed below to boot up the device.
*Click the power button at the front or rear panel and then boot up the device. After device booted up, the system is in multiple-channel display mode by default.
+
1. Connect the device to the monitor and then connect a mouse.
 +
2. Connect power cable.
 +
3. Click the power button at the front or rear panel and then boot up the device. After device booted up, the system is in multiple-channel display mode by default.
 +
 
 +
====Shutdown====
 +
* When you see corresponding dialogue box “System is shutting down…” Do not click power on-off button directly.
 +
* Do not unplug the power cable or click power on-off button to shutdown device directly when device is running (especially when it is recording.)
 +
 
 +
 
 +
There are three ways for you to log out.
 +
 
 +
# Main menu ('''RECOMMENDED''')
 +
 
 +
From Main Menu->Shutdown, select shutdown from dropdown list.
 +
 
 +
Click OK button, you can see device shuts down.
 +
 
 +
 
 +
# From power on-off button on the front panel or remote control
 +
 
 +
Press the power on-off button on the NVR front panel or remote control for more than 3 seconds to shutdown the device.
 +
 
 +
 
 +
# From power on-off button on the rear panel.

Revision as of 16:31, 23 October 2015

File:Standalone_DVR_Quick_Start_Guide_V1.0.0.pdf

Boot up and Shutdown

Boot up

Before the boot up, please make sure:

  • For device security, please connect the NVR to the power adapter first and then connect the device to the power socket.
  • The rated input voltage matches the device power on-off button. Please make sure the power wire connection is OK. Then click the power on-off button.
  • Always use the stable current, if necessary UPS is a best alternative measure.

Please follow the steps listed below to boot up the device. 1. Connect the device to the monitor and then connect a mouse. 2. Connect power cable. 3. Click the power button at the front or rear panel and then boot up the device. After device booted up, the system is in multiple-channel display mode by default.

Shutdown

  • When you see corresponding dialogue box “System is shutting down…” Do not click power on-off button directly.
  • Do not unplug the power cable or click power on-off button to shutdown device directly when device is running (especially when it is recording.)


There are three ways for you to log out.

  1. Main menu (RECOMMENDED)

From Main Menu->Shutdown, select shutdown from dropdown list.

Click OK button, you can see device shuts down.


  1. From power on-off button on the front panel or remote control

Press the power on-off button on the NVR front panel or remote control for more than 3 seconds to shutdown the device.


  1. From power on-off button on the rear panel.