Difference between revisions of "SNMP"
(Created page with "==SNMP==") |
|||
| Line 1: | Line 1: | ||
==SNMP== | ==SNMP== | ||
| + | |||
| + | SNMP allows the communication between the network management work station software and the | ||
| + | proxy of the managed device. Please install the software such as MG MibBrowser 8.0c software or | ||
| + | establish the SNMP service before you use this function. You need to reboot the device to activate the | ||
| + | new setup. | ||
| + | |||
| + | |||
| + | Please refer to the following sheet for detailed information. | ||
| + | Parameter Function | ||
| + | SNMP Version Check SNMP v1, device only process v1 info. | ||
| + | Check SNMP v2, device only process v2 info. | ||
| + | Check SNMP v3, can set username, password and | ||
| + | encryption method. Server calibrate corresponding | ||
| + | username, password and encryption method too access | ||
| + | device and v1/v2 are unavailable. | ||
| + | SNMP port The listening port of the proxy program of the device. It is a | ||
| + | UDP port not a TCP port. The value ranges from 1 to 65535. | ||
| + | The default value is 161 | ||
| + | Community It is a string, as command between management and proxy, , | ||
| + | defining a proxy, and a manager’s authentication. | ||
| + | Read community Read-only access to all SNMP targets, default is public. | ||
| + | Note: Only number, letter, _, and – supported. | ||
| + | Write community Read/write access to all SNMP targets, default is private. | ||
| + | Note: Only number, letter, _, and – supported. | ||
| + | Trap address The destination address of the Trap information from the | ||
| + | proxy program of the device. | ||
| + | Trap SNMP trap is a proxy message sent to admin as important | ||
| + | event notice or status change. | ||
| + | Trap Address Address where to send Trap message. | ||
| + | Trap Port Port which send Trap message, default is 162, range | ||
| + | 1~65535 | ||
| + | |||
| + | |||
| + | Check SNMP v3 version and SNMP port, read community, write community, Trap address, | ||
| + | Trap port are same with SNMP v1 and SNMP v2 versions. Only when SNMP version is | ||
| + | SNMP v3, user need to configure parameter in chart. | ||
| + | Parameter Function | ||
| + | SNMP Version SNMP v3 | ||
| + | Read-only | ||
| + | Username | ||
| + | Default is public. | ||
| + | Note: | ||
| + | Name only can be number, letter and underline. | ||
| + | Read/Write | ||
| + | Username | ||
| + | Default is private. | ||
| + | Note: | ||
| + | Name only can be number, letter and underline. | ||
| + | Authentication You may select MD5 or SHA, default is MD5. | ||
| + | Authentication | ||
| + | Password Password not less than 8 characters. | ||
| + | Encryption Default is CBC-DES. | ||
| + | |||
| + | Check SNMP v3 version and SNMP port, read community, write community, Trap address, | ||
| + | Trap port are same with SNMP v1 and SNMP v2 versions. Only when SNMP version is | ||
| + | SNMP v3, user need to configure parameter in chart. | ||
| + | Parameter Function | ||
| + | SNMP Version SNMP v3 | ||
| + | Read-only | ||
| + | Username | ||
| + | Default is public. | ||
| + | Note: | ||
| + | Name only can be number, letter and underline. | ||
| + | Read/Write | ||
| + | Username | ||
| + | Default is private. | ||
| + | Note: | ||
| + | Name only can be number, letter and underline. | ||
| + | Authentication You may select MD5 or SHA, default is MD5. | ||
| + | Authentication | ||
| + | Password Password not less than 8 characters. | ||
| + | Encryption Default is CBC-DES. | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | ----------------------------------------------------------------- | ||
| + | |||
| + | NVR | ||
| + | |||
| + | SNMP | ||
| + | SNMP is an abbreviation of Simple Network Management Protocol. It provides the basic network | ||
| + | management frame of the network management system. The SNMP widely used in many environments. | ||
| + | It is used in many network device, software and system. | ||
| + | You can set in the following interface. | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | Please enable the SNMP function. Use the corresponding software tool (MIB Builder and MG-SOFT MIB | ||
| + | Browser. You still need two MIB file: BASE-SNMP-MIB, NVR-SNMP-MIB) to connect to the device. You | ||
| + | can get the device corresponding configuration information after successfully connection. | ||
| + | Please follow the steps listed below to configure. | ||
| + | In Figure 4-107, check the box to enable the SNMP function. Input the IP address of the PC than is | ||
| + | running the software in the Trap address. You can use default setup for the rest items. | ||
| + | Compile the above mentioned two MIB file via the software MIB Builder. | ||
| + | Run MG-SOFT MIB Browser to load the file from the previous step to the software. | ||
| + | Input the device IP you want to manage in the MG-SOFT MIB Browser. Please set the corresponding | ||
| + | version for your future reference. | ||
| + | Open the tree list on the MG-SOFT MIB Browser; you can get the device configuration. Here you can | ||
| + | see the device has how many video channels, audio channels, application version and etc. | ||
| + | Note | ||
| + | Port conflict occurs when SNMP port and Trap port are the same. | ||
Revision as of 23:52, 30 March 2016
SNMP
SNMP allows the communication between the network management work station software and the proxy of the managed device. Please install the software such as MG MibBrowser 8.0c software or establish the SNMP service before you use this function. You need to reboot the device to activate the new setup.
Please refer to the following sheet for detailed information.
Parameter Function
SNMP Version Check SNMP v1, device only process v1 info.
Check SNMP v2, device only process v2 info.
Check SNMP v3, can set username, password and
encryption method. Server calibrate corresponding
username, password and encryption method too access
device and v1/v2 are unavailable.
SNMP port The listening port of the proxy program of the device. It is a
UDP port not a TCP port. The value ranges from 1 to 65535.
The default value is 161
Community It is a string, as command between management and proxy, ,
defining a proxy, and a manager’s authentication.
Read community Read-only access to all SNMP targets, default is public.
Note: Only number, letter, _, and – supported.
Write community Read/write access to all SNMP targets, default is private.
Note: Only number, letter, _, and – supported.
Trap address The destination address of the Trap information from the
proxy program of the device.
Trap SNMP trap is a proxy message sent to admin as important
event notice or status change.
Trap Address Address where to send Trap message.
Trap Port Port which send Trap message, default is 162, range
1~65535
Check SNMP v3 version and SNMP port, read community, write community, Trap address,
Trap port are same with SNMP v1 and SNMP v2 versions. Only when SNMP version is
SNMP v3, user need to configure parameter in chart.
Parameter Function
SNMP Version SNMP v3
Read-only
Username
Default is public.
Note:
Name only can be number, letter and underline.
Read/Write
Username
Default is private.
Note:
Name only can be number, letter and underline.
Authentication You may select MD5 or SHA, default is MD5.
Authentication
Password Password not less than 8 characters.
Encryption Default is CBC-DES.
Check SNMP v3 version and SNMP port, read community, write community, Trap address, Trap port are same with SNMP v1 and SNMP v2 versions. Only when SNMP version is SNMP v3, user need to configure parameter in chart. Parameter Function SNMP Version SNMP v3 Read-only Username Default is public. Note: Name only can be number, letter and underline. Read/Write Username Default is private. Note: Name only can be number, letter and underline. Authentication You may select MD5 or SHA, default is MD5. Authentication Password Password not less than 8 characters. Encryption Default is CBC-DES.
NVR
SNMP SNMP is an abbreviation of Simple Network Management Protocol. It provides the basic network management frame of the network management system. The SNMP widely used in many environments. It is used in many network device, software and system. You can set in the following interface.
Please enable the SNMP function. Use the corresponding software tool (MIB Builder and MG-SOFT MIB
Browser. You still need two MIB file: BASE-SNMP-MIB, NVR-SNMP-MIB) to connect to the device. You
can get the device corresponding configuration information after successfully connection.
Please follow the steps listed below to configure.
In Figure 4-107, check the box to enable the SNMP function. Input the IP address of the PC than is
running the software in the Trap address. You can use default setup for the rest items.
Compile the above mentioned two MIB file via the software MIB Builder.
Run MG-SOFT MIB Browser to load the file from the previous step to the software.
Input the device IP you want to manage in the MG-SOFT MIB Browser. Please set the corresponding
version for your future reference.
Open the tree list on the MG-SOFT MIB Browser; you can get the device configuration. Here you can
see the device has how many video channels, audio channels, application version and etc.
Note
Port conflict occurs when SNMP port and Trap port are the same.
