:Intrusion
Contents
- 1 Intrusion
- 1.1 Instructions
- 1.1.1 Description
- 1.1.2 Prerequisites
- 1.1.3 Video Instructions
- 1.1.4 Step By Step Instructions
- 1.1.5 Description
- 1.1.6 Prerequisites
- 1.1.7 Video Instructions
- 1.1.8 Step By Step Instructions
- 1.1.9 Prerequisites
- 1.1.10 Video Instructions
- 1.1.11 Step By Step Instructions
- 1.1.12 Description
- 1.1.13 Prerequisites
- 1.1.14 Video Instructions
- 1.1.15 Step By Step Instructions
- 1.1.16 Prerequisites
- 1.1.17 Video Instructions
- 1.1 Instructions
Intrusion
Instructions
SystemUI Old
Description
Intrusion Detection is to detect if there is any object entering or leaving the area, the rule will trigger when crossing the area perimeter. Supports enter, leave, and enter & leave three direction selection, it can activate record, snapshot, and alarm according to the judgment result.
Application Scene: It is similar to warning line. It needs to leave some space for target movement outside the perimeter if it is to detect enter and leave event; It can only be applied to the scene where the target is sparse and there is rarely any covering between the targets, such as the perimeter without any guard. It will trigger alarm when the target is entering or leaving the area.
Prerequisites
- Intelligent Network Camera or an HDCVI Camera that is connected to a HDCVI DVR that has intelligent features.
- Updated firmware that supports intelligent features.
- Internet Explorer.
Video Instructions
Step By Step Instructions
1. From Live View, right click then select Main Menu
2. Click Event
3. Click Smart Plan
4. Use the dropdown box to select the channel
Click the IVS icon (lightbulb) to enable
5. Click Apply to save
6. Click IVS
7. Use the dropdown box to select the channel
Click Add to create a new IVS rule
8. The rule will appear in the list
Use the dropdown box to select Intrusion
9. Click the pencil icon under Draw to begin drawing the detection area
10. The video will fullscreen
Left click inside the frame to begin drawing
Right click to finish drawing
The Rule name will confirm the rule has been created
11. Use the interface to make any additional parameters settings:
- Name - Name of the rule
- Appears - Alarm is triggered when the target appears in the designated area and within the alarm time
- Cross - Alarm is triggered when the target crosses (enter or exists) the area in the designated area and within the alarm time
- Direction
Click OK to save
12. Click Apply to save
SystemUI New
Description
Intrusion Detection is to detect if there is any object entering or leaving the area, the rule will trigger when crossing the area perimeter. Supports enter, leave, and enter & leave three direction selection, it can activate record, snapshot, and alarm according to the judgment result.
Application Scene: It is similar to warning line. It needs to leave some space for target movement outside the perimeter if it is to detect enter and leave event; It can only be applied to the scene where the target is sparse and there is rarely any covering between the targets, such as the perimeter without any guard. It will trigger alarm when the target is entering or leaving the area.
Prerequisites
- Intelligent Network Camera or an HDCVI Camera that is connected to a HDCVI DVR that has intelligent features.
- Updated firmware that supports intelligent features.
- Internet Explorer.
Video Instructions
Step By Step Instructions
1. From the Main Menu
Click AI
2. Click Parameters
3. Click Smart Plan
4. Use the dropdown box to select the channel
Click the IVS icon (lightbulb) to enable
5. Click Apply
6. Click IVS
7. Use the dropdown box to select the channel
Click Add to create a new IVS rule
8. The rule will appear in the list
Use the dropdown box under Type to select Intrusion
9. Click the Pencil icon under Draw to begin drawing the detection area
10. The video will fullscreen
Left click inside the video frame to begin drawing
Right click to finish drawing
The Rule name will confirm the rule has been created
11. Use the interface to make any additional parameters settings:
- Name - Name of the rule
- Action
- Appear - Alarm is triggered when the target appears in the designated area and within the alarm time
- Cross - Alarm is triggered when the target crosses (enter or exists) the area in the designated area and within the alarm time
- Direction
Click OK to save
12. Click the Gear icon under Trigger to configure a response when the rule is triggered
13. Use the interface to enable the desired Trigger functions
Click Apply to save
14. Click Apply to save all settings
WebUI Old
Intrusion Detection is to detect if there is any object entering or leaving the area, the rule will trigger when crossing the area perimeter. Supports enter, leave, and enter & leave three direction selection, it can activate record, snapshot, and alarm according to the judgment result.
Application Scene: It is similar to warning line. It needs to leave some space for target movement outside the perimeter if it is to detect enter and leave event; It can only be applied to the scene where the target is sparse and there is rarely any covering between the targets, such as the perimeter without any guard. It will trigger alarm when the target is entering or leaving the area.
Prerequisites
- Intelligent Network Camera or an HDCVI Camera that is connected to a HDCVI DVR that has intelligent features.
- Updated firmware that supports intelligent features.
- Internet Explorer.
Video Instructions
Step By Step Instructions
1. Log into device using the Web Service.
2. Select Setup -> Select Event -> IVS
3. Under the IVS section, click the + and use the item that appears to set a name for your rule and in the drop down, define the rule type, in this case, "Intrusion" then select "Draw Rule.
4. Next, use your mouse to click and define the lines for the area you'd like to establish the rule for, then define the Action and Direction. In this example we'll use Cross and Enter to notify of entry into the region.
After clicking 'Draw Rule'
Region defined.
5. By default the schedule for the rule is set up for 24/7, to edit this go to 'Setup' by working period. Here you can make changes to the days and time periods in which it is active.
Working Period Setup
Working Period Edit window
6. Next be sure to check any other options you may want such as Record & Record Delay, Snapshot, Relay out (1, 2, or both)alarm Delay and email. Note: For instructions on email setup see Email Setup
WebUI New
Description
This guide will show how to setup the Intrusion IVS feature at the WebUI with New GUI
Prerequisites
Video Instructions
Step By Step Instructions
1. From the Main Menu
Click AI
2. Click Parameters
3. Click Smart Plan
4. Use the dropdown box to select the channel
Click the IVS icon (lightbulb) to enable
5. Click OK to save
6. Click IVS
7. Use the dropdown box to select the channel
Click the + to add a new IVS rule
8. The rule will appear in the list
Use the dropdown box under Type to select Intrusion
9. Click Draw Rule to begin drawing the detection area
10. Left click inside the video frame to begin drawing
Right click to finish drawing
The rule name will confirm when drawing is complete
11. Use the Target interface to configure the Max/Min size for detection (if required)
12. Under Parameters Config
Use the interface to make any additional parameters settings for the rule:
- Name - Name of the rule
- Action
- Appear - Alarm is triggered when the target appears in the designated area and within the alarm time
- Cross - Alarm is triggered when the target crosses (enter or exists) the area in the designated area and within the alarm time
- Direction
13. Use the interface to enable the desired Trigger functions and schedule (if required)
Under More Setting
There are additional trigger actions to set for the rule
- Buzzer
- Log
- Alarm Upload
- Send Email
Make any desired changes and click OK to save
14. Click OK to save all settings
SmartPSS
This guide will show how to setup the Intrusion IVS feature in SmartPSS
Prerequisites
- Dahua device with Intrusion IVS feature (added to SmartPSS)
Video Instructions
Step by Step Instructions
1, From the Main Menu of SmartPSS
Click Device CFG
2. Click to select the device from the device tree on the left
3. Click to expand Event
4. Click Intelligent Analyse
5. Confirm the preset (if required)
Click Next
6. Use the dropdown box to select the channel/preset
Click to select the IVS icon
7. Click Next
8. Under Detect Region
The detection zone can be configured, by default it will be the entire video frame
9. Under Rule config
Click Add rule to create a new IVS rule
10. Use the dropdown box to change Rule type to Intrusion
11. Left click inside the video frame to begin drawing the IVS rule
Right click to finish drawing, a prompt will confirm when the rule has been created
12. Click Config to make additional parameters adjustments
13. Under Parameters
- Action List
- Appear - Alarm is triggered when the target appears in the designated area and within the alarm time
- Cross - Alarm is triggered when the target crosses (enter or exists) the area in the designated area and within the alarm time
- Direction
14. Under Arming Schedule, the schedule for the rule can be created, by default it will be 24/7
15. Under Alarm, the various triggers for when the rule is triggered can be configured
Click Save
16. Click Save to save all settings
DSS Express S
