IPCWebInterface

Main Menu

There are four sections:

• Section 1: Encode setup bar
• Section 2: System menu
• Section 3: Window function option bar
• Section 4: Window adjust bar

Parameter	Function
Main stream	Streaming media protocol connection, under main stream config, monitor video or not. Generally for storage and monitor.
Sub (Extra) stream 1	Streaming media protocol connection, under sub stream 1 config, monitor video or not. When network bandwidth is insufficient, it substitutes main stream for monitoring.
Sub (Extra) stream 2	Streaming media protocol connection, under sub stream 2 config, monitor video or not. When network bandwidth is insufficient, it substitutes main stream for monitoring.
Protocol	You can select stream media protocol from the dropdown list. There are three options: TCP/UDP/Multicast

System Menu

Video Window Function Menu

SN	Parameter	Function
1	Alarm output	It shows if there is any alarm output, status description is as follows: Red: means there is alarm output. Grey: means alarm is over. Click on the button to force alarm to be on or off.
2	Zoom in	When the video is in the original status, click it you can select any zone to zoom in. In the non-original status, you can drag the zoom-in zone in specified range. Right click mouse to restore previous status. Click it; you can use the middle button of the mouse to zoom in/out the video size.
3	Snapshot	Click on the button to snapshot, save picture to path in Ch 5.1.2.5.
4	Triple snap	Click it, system can snap at 1f/s. All images are saved to path in Ch 5.1.2.5.
5	Record	Click it, system can record. All images are saved to path in Ch 5.1.2.5.
6	Easy focus	Click it, you can see there are two parameters on the preview video：AF Peak and AF Max. AF Peak: It is to display the video definition during the focus process. AF Max: It is the most suitable value for the video definition. The close the AF Peak and AF Max is, the better the focus effect is.
7	Audio output	Turn on or off audio when you are monitoring.
8	Bidirectional talk	Click it to start or end bidirectional talk.
9	Help	Click it to open help file.

Image Adjustment

Parameter		Function
Video setup	It is to adjust monitor video brightness.	Note: All the operations here apply to WEB end only. Please go to Setup->Camera->Conditions to adjust corresponding items.
	It is to adjust monitor video contrastness.
	It is to adjust monitor video hue.
	It is to adjust monitor video saturation.
	Reset		Restore brightness, contrastness saturation and hue to system default setup.

Video Window Setup

Original Size	Click this button to go to original size. It is to display the actual size of the video stream. It depends on the resolution of the bit stream.
Full Screen	Click it to go to full-screen mode. Double click the mouse or click the Esc button to exit the full screen.
Width and Height Ratio	Click it to restore original ratio or suitable window.
Fluency Adjustment	There are three levels of fluency for you to select (real-time, normal, fluent). The default is normal.
Rules Info	Click the button, preview image will display intelligent rules after enabling; it is “enable” by default.
Focus zoom	Click this button and the focus zooming interface appears on the right of preview interface, click left mouse button to adjust focus zooming configuration. Note: • The product series which support motorized zoom, synchronous focus and back focus have this button. • Auto-focus after zoom and focus adjustment.
Fisheye	Click the button, installation mode and display mode interface will show up on the right of the preview interface, see Figure 2-8, single click to switch different installation mode and display mode, default is enable. Note: Only supported by fisheye devices.

Fisheye Menu Part 1

Parameter	Function
Zoom	Adjust the focal length of the lens by clicking or long pressing “+”“-”buttons. Step length is used to adjust the length of one step with one click.
Focus	Adjust the sharpness of the lens by clicking or long pressing“+”、“-” buttons. Step length is used to adjust the length of one step with one click.
Auto-focus	Click to adjust the image definition automatically. Note: Other lens operations are not allowed during the process of auto-focus.
Reset	Reset the lens to zero position to eliminate the accumulative error of lens.  Note: Please reset when the image adjustment is not clear or operating zoom focus many times.
Refresh	Synchronize the location of drag slider of lens and zoom focus after hardware zoom focusing.

Fisheye Menu Part 2