Difference between revisions of "IVS:Abandoned Missing Object"

From Dahua Wiki

Jump to: navigation, search
(Installation Suggestions)
(Installation Suggestions)
 
Line 4: Line 4:
 
==Installation Suggestions==
 
==Installation Suggestions==
 
* The target should be less than 10% of the image.
 
* The target should be less than 10% of the image.
 +
* Viewing angle >20 degrees
 +
* Installation height
 +
** Indoor height - no lower than 3 meters
 +
** Outdoor height - 5-10 meters
 
* The target size in the image should not be less than 15×15 pixels.
 
* The target size in the image should not be less than 15×15 pixels.
 
* Brightness difference between the target and the background should not be less than 10 greyscale.
 
* Brightness difference between the target and the background should not be less than 10 greyscale.

Latest revision as of 23:46, 4 December 2019

Abandoned/Missing Object

Description

Abandoned/missing function is used to detect if there are people, vehicle and objects abandoned or missing in some areas in the monitoring scene; it can trigger an alarm when the target object stays or is missing for a time which exceeds the desired time.

Installation Suggestions

  • The target should be less than 10% of the image.
  • Viewing angle >20 degrees
  • Installation height
    • Indoor height - no lower than 3 meters
    • Outdoor height - 5-10 meters
  • The target size in the image should not be less than 15×15 pixels.
  • Brightness difference between the target and the background should not be less than 10 greyscale.
  • The target should be continuously present in the image for no less than two seconds, and the moving distance of the target should be larger than its width and no less than 15 pixels (CIF image).
  • Reduce the complexity of surveillance scene as possible as you can. Intelligent analysis function is not recommended to be used in scene with dense targets and frequent illumination change.
  • Avoid areas such as glass, reflective ground, water surface, and areas interfered by branch, shadow and mosquito. Avoid backlight scene and direct light.

Optional Functions

  • Set shortest keep time - the time from when the target is abandoned or missing to when the alarm is triggered
  • Working period setting - by default is set to 24/7
  • Supports alarm linkage: Record, relay out, send email and snapshot
  • Target filter can be set for a max and min target, which means the maximum and minimum target size for an object to be detected

Instructions

Icon for type SystemUI Old.pngSystemUI Old

Description

This guide will show how to setup the Abandoned Object / Missing feature at the SystemUI with OldUI

Abandoned object/missing function is used to detect if there are people, vehicle and objects abandoned or missing in some areas in the monitoring scene; it can trigger an alarm when the target object stays or is missing for a time which exceeds the desired time.

Prerequisites

  • Dahua device with Abandoned / Missing IVS feature

Video Instructions


Step By Step Instructions

Abandoned

1. From Live View right click to access the menu and select Main Menu

Abandoned Missing - SystemUI OldUI - 1.jpg

2. Click Event

Abandoned Missing - SystemUI OldUI - 2.jpg

3. Use the dropdown box to select the channel

Click the IVS icon (Lightbulb) to enable the Smart Plan

Abandoned Missing - SystemUI OldUI - 3.jpg

4. Click Apply

Abandoned Missing - SystemUI OldUI - 4.jpg

5. Click IVS

Abandoned Missing - SystemUI OldUI - 5.jpg

6. Click Add to create a new IVS rule

Abandoned Missing - SystemUI OldUI - 6.jpg

7. Use the dropdown box to change rule Type to Abandoned

Abandoned Missing - SystemUI OldUI - 7.jpg

8. Click the Pencil icon under Draw to create the detection zone

Abandoned Missing - SystemUI OldUI - 8.jpg

9. The video will fullscreen

Left click inside the window to begin drawing the detection zone

Abandoned Missing - SystemUI OldUI - 9.jpg

10. Right click to finish drawing the zone

The Rule name will confirm the rule has been created

Click OK to save

Abandoned Missing - SystemUI OldUI - 10.jpg

11. Click Apply to save all settings

Abandoned Missing - SystemUI OldUI - 11.jpg

Missing

1. From Live View right click to access the menu and select Main Menu

Abandoned Missing - SystemUI OldUI - 1.jpg

2. Click Event

Abandoned Missing - SystemUI OldUI - 2.jpg

3. Use the dropdown box to select the channel

Click the IVS icon (Lightbulb) to enable the Smart Plan

Abandoned Missing - SystemUI OldUI - 3.jpg

4. Click Apply

Abandoned Missing - SystemUI OldUI - 4.jpg

5. Click IVS

Abandoned Missing - SystemUI OldUI - 5.jpg

6. Click Add to create a new IVS rule

Abandoned Missing - SystemUI OldUI - 6.jpg

7. Use the dropdown box to change rule Type to Missing

Abandoned Missing - SystemUI OldUI - 12.jpg

8. Click the Pencil icon under Draw to create the detection zone

Abandoned Missing - SystemUI OldUI - 13.jpg

9. The video will fullscreen

Left click inside the window to begin drawing the detection zone

Abandoned Missing - SystemUI OldUI - 14.jpg

10. Right click to finish drawing the zone

The Rule name will confirm the rule has been created

Click OK to save

Abandoned Missing - SystemUI OldUI - 15.jpg

11. Click Apply to save all settings

Abandoned Missing - SystemUI OldUI - 16.jpg

Icon for type SystemUI New.pngSystemUI New

Description

This guide will show how to setup the Abandoned Object / Missing feature at the SystemUI with NewGUI

Abandoned object/missing function is used to detect if there are people, vehicle and objects abandoned or missing in some areas in the monitoring scene; it can trigger an alarm when the target object stays or is missing for a time which exceeds the desired time.

Prerequisites

  • Dahua device with Abandoned / Missing IVS feature

Video Instructions

Missing Object

Abandoned Object

Step By Step Instructions

Missing

1. From the Main Menu click AI

Missing - SystemUI - NewGUI - 0.jpg

2. Click Parameters

Missing - SystemUI - NewGUI - 1.jpg

3. Click Smart Plan

Missing - SystemUI - NewGUI - 2.jpg

4. Use the dropdown box to select the channel

Click the IVS icon (Lightbulb) to enable the Smart Plan

Missing - SystemUI - NewGUI - 3.jpg

5. Click Apply

Missing - SystemUI - NewGUI - 4.jpg

6. Click IVS

Missing - SystemUI - NewGUI - 5.jpg

7. Click Add to create a new IVS rule.

Missing - SystemUI - NewGUI - 6.jpg

8. Use the dropdown box to change rule Type to Missing

Missing - SystemUI - NewGUI - 7.jpg

Missing - SystemUI - NewGUI - 8.jpg

9. Click the Pencil icon under Draw to create the detection zone

Missing - SystemUI - NewGUI - 9.jpg

10. The video will fullscreen

Left click inside the window to begin drawing the detection zone

Missing - SystemUI - NewGUI - 10.jpg

11. Right click to finish drawing the zone

The Rule name will confirm the rule has been created

Click OK to save

Missing - SystemUI - NewGUI - 11.jpg

12. Click Apply to save all settings

Missing - SystemUI - NewGUI - 12.jpg

Abandoned

1. From the Main Menu click AI

Missing - SystemUI - NewGUI - 0.jpg

2. Click Parameters

Missing - SystemUI - NewGUI - 1.jpg

3. Click Smart Plan

Missing - SystemUI - NewGUI - 2.jpg

4. Use the dropdown box to select the channel

Click the IVS icon (Lightbulb) to enable the Smart Plan

Missing - SystemUI - NewGUI - 3.jpg

5. Click Apply

Missing - SystemUI - NewGUI - 4.jpg

6. Click IVS

Missing - SystemUI - NewGUI - 5.jpg

7. Use the dropdown box to change rule Type to Abandoned

Missing Object - SystemUI NewGUI - 1.jpg

8. Click the Pencil icon under Draw to create the detection zone

Missing Object - SystemUI NewGUI - 2.jpg

9. The video will fullscreen

Left click inside the window to begin drawing the detection zone

Missing Object - SystemUI NewGUI - 3.jpg

10. Right click to finish drawing the zone

The Rule name will confirm the rule has been created

Click OK to save

Missing Object - SystemUI NewGUI - 4.jpg

11. Click Apply to save all settings

Missing Object - SystemUI NewGUI - 5.jpg

Icon for type WebUI Old.pngWebUI Old

===Description===

Application Scene: It can be applied to the scene where the target is sparse and there is no obvious or frequent light change. Missing alarm will increase in the scene where target density is high and there is frequent covering; false alarm will increase in the scene where there are too many people. As for the detection area, it needs to be simple; it is not suitable for the too complicated area.

Description: object abandoned means that it is to detect if there is any object abandoned in the designated detection area and surpass the set time. It will activate record, snapshot and alarm according to the judgment result. Object missing means that it is to detect if there is any object moved in the designated area and surpass the set time. It will activate record, snapshot and alarm according to the judgment result.

Prerequisites

  • Dahua device with Abandoned / Missing IVS feature

Video Instructions

Missing Object

Abandoned Object

Step By Step Instructions

1.Log into device using the Web Service.

1GenericStart.PNG


2.Select Setting -> Event -> IVS.

2GenericStart.PNG


3. Next to Rule Type click "+" in the new rule that shows below, define the Rule Name and in the drop down select Abandon Object or Missing Object as the rule type. In this example we'll be using Abandon Object.

AbandonObject 1.PNG

4. Once the Rule type and name have been set, Define your Keep time (The time it takes until an object is flagged) and whether you want to save a recording/snapshot or have an email notification sent out for it. In this example email and snapshot will be used. For instructions on setting up email functionality see Email Setup

AbandonObject3.png

5. By default the rule will be active on a 24/7 basis, if you need to modify the schedule, use the Setup button next to "Working Period" in the window that appears, you can define the time periods (up to 6 per day) for the rule to be active.

6. To define the area of the rule, use "Draw Rule" to set the area; left click and use your mouse to draw your region. Once Finished click save to commit your settings.

AbandonObject6.png

Icon for type WebUI New.pngWebUI New

===Description===

This guide will show how to setup the Abandoned Object / Missing feature at the WebUI with NewGUI

Abandoned object/missing function is used to detect if there are people, vehicle and objects abandoned or missing in some areas in the monitoring scene; it can trigger an alarm when the target object stays or is missing for a time which exceeds the desired time.

Prerequisites

Video Instructions

Step By Step Instructions

Abandoned

1. From the Main Menu

Click AI

Abandoned Missing - WebUI New - 1.jpg

2. Click Parameters

Abandoned Missing - WebUI New - 2.jpg

3. Click Smart Plan

Abandoned Missing - WebUI New - 3.jpg

4. Use the dropdown box to select the channel

Click the IVS icon (Lightbulb) to enable the Smart Plan

Abandoned Missing - WebUI New - 4.jpg

5. Click OK to save

Abandoned Missing - WebUI New - 5.jpg

6. Click IVS

Abandoned Missing - WebUI New - 6.jpg

7. Click the + to create a new IVS rule

Abandoned Missing - WebUI New - 7.jpg

8. Use the dropdown box to change rule Type to Abandoned

Abandoned Missing - WebUI New - 8.jpg

9. Click Draw Rule to create the detection area

Abandoned Missing - WebUI New - 9.jpg

10. Left click inside the window to begin drawing the detection zone

Abandoned Missing - WebUI New - 10.jpg

11. Right click to finish drawing the zone

The Rule name will confirm the rule has been created

Abandoned Missing - WebUI New - 11.jpg

12. Use the Target interface to adjust the Max/Min size for object detection

Abandoned Missing - WebUI New - 12.jpg

13. Click OK to save all settings

Abandoned Missing - WebUI New - 13.jpg

Missing

1. From the Main Menu

Click AI

Abandoned Missing - WebUI New - 1.jpg

2. Click Parameters

Abandoned Missing - WebUI New - 2.jpg

3. Click Smart Plan

Abandoned Missing - WebUI New - 3.jpg

4. Use the dropdown box to select the channel

Click the IVS icon (Lightbulb) to enable the Smart Plan

Abandoned Missing - WebUI New - 4.jpg

5. Click OK to save

Abandoned Missing - WebUI New - 5.jpg

6. Click IVS

Abandoned Missing - WebUI New - 6.jpg

7. Click the + to create a new IVS rule

Abandoned Missing - WebUI New - 7.jpg

8. Use the dropdown box to change rule Type to Missing

Abandoned Missing - WebUI New - 14.jpg

9. Click Draw Rule to create the detection area

Abandoned Missing - WebUI New - 15.jpg

10. Left click inside the window to begin drawing the detection zone

Abandoned Missing - WebUI New - 16.jpg

11. Right click to finish drawing the zone

The Rule name will confirm the rule has been created

Abandoned Missing - WebUI New - 17.jpg

12. Click OK to save all settings

Abandoned Missing - WebUI New - 18.jpg

Icon for type SmartPSS.pngSmartPSS

===Description===

This guide will show how to setup the Abandoned Object / Missing feature in SmartPSS

Abandoned object/missing function is used to detect if there are people, vehicle and objects abandoned or missing in some areas in the monitoring scene; it can trigger an alarm when the target object stays or is missing for a time which exceeds the desired time.

Prerequisites

  • SmartPSS
  • Dahua device with Abandoned / Missing IVS feature (also added to SmartPSS)
  • Upgraded devices to latest firmware

Video Instructions

Abandoned

Missing

Step by Step Instructions

1. From the Main Menu of SmartPSS

Click DeviceCFG

Abandoned Missing - SmartPSS - 1.jpg

2. Select the device from the device tree on the left side of the screen

Abandoned Missing - SmartPSS - 2.jpg

3. Click the Event section to expand

Abandoned Missing - SmartPSS - 3.jpg

4. Click Intelligent Analyse

Abandoned Missing - SmartPSS - 4.jpg

5. Click the IVS icon to enable

Click Next

Abandoned Missing - SmartPSS - 5.jpg

6. Under Detect Region tab

Use the Re-draw/Delete buttons to create the Detection Zone for the IVS rule. By default it will be the entire frame

Abandoned Missing - SmartPSS - 6.jpg

7. Under Rule config tab

Click Add Rule

to add a new IVS rule

Abandoned Missing - SmartPSS - 7.jpg

8. The new rule will appear in the list

Use the dropdown box next to Rule type to select the IVS type - Abandoned Object or Missing Object

Abandoned Missing - SmartPSS - 8.jpg

9. Left click inside the video frame to begin drawing the detection area

Abandoned Missing - SmartPSS - 9.jpg

10. Right click to finish drawing the area

Abandoned Missing - SmartPSS - 10.jpg

11. Click Save

Abandoned Missing - SmartPSS - 11.jpg