Difference between revisions of "LincX2PRO/DB11 Physical Install"
(→Step by Step Instructions) |
(→Step by Step Instructions) |
||
| Line 63: | Line 63: | ||
<div class="toccolours mw-collapsible mw-collapsed"> | <div class="toccolours mw-collapsible mw-collapsed"> | ||
[[File:DMSS_New_Icon.png|70px]]<span style="font-size:180%;">'''Mobile: DMSS '''</span> | [[File:DMSS_New_Icon.png|70px]]<span style="font-size:180%;">'''Mobile: DMSS '''</span> | ||
| − | <div class="mw-collapsible-content">{{Template: | + | <div class="mw-collapsible-content">{{Template:Ring_Linkage_Setup_MobileUI_New_DMSS}}</div> |
</div> | </div> | ||
Revision as of 16:21, 7 April 2020
Contents
DB11 Physical Install
Description
This article will cover how to physically connect a DB11 to a door chime
Prerequisites
- DB11 (And all the parts included in the box)
- gDMSS Plus or iDMSS Plus
- Dahua Online Account
- A Mechanical or Electronic Door Chime
Video Instructions
Step by Step Instructions
IMPORTANT NOTICE: Disable the power to your doorbell and door chime before beginning physical installation
1. If not already done, disconnect the wire from the existing doorbell, that goes between it and the "FRONT" terminal on the door chime (#1 below).
Disconnect the wire from the exisiting doorbell, that goes between it and the Power Transformer (#2 below)
2. Flip over the DB11 and connect the Wire Harness wires, included in the box, to the back of DB11
3. From the DB11 and the door chime, twist the two wires, one from the end of the Wire Harness and one from the door chime, and connect them together with a Wire Nut or Clip (included in the box).
Repeat this for the other set of wires from the DB11 and the Power Transformer.
4. The door chime that is already installed will either be Electronic or Mechanical.
Make sure the two wires are already connected to the FRONT and TRANS connections. If they are not, adjust them so they are.
5. If you are using a Mechanical door chime skip to Step 7. If you are using an Electronic door chrime continue from here.
With the Electronic door chime, you will need to add the Chime Kit (included in the box)
6. Connect the wire set shown below (included in the box) to the Chime Kit with the green Terminal Block (also included in the box).
Connect the wire set in line with the DB11, door chime, and AC Power Transformer in the configuration shown in the diagram below:
7. The DB11 will now be installed in place of your previous doorbell.
It is safe to turn the power back on to the door bell system/power transformer
8. Open your mobile app and follow instruction below.
Note: There are two mobile apps that available to support this product series.
Select your DB11 from the list of devices.
9. From the DB11 Device Settings screen select "Ring Linkage".
10. Select "New Linkage".
11. Select "Associate Third-party Chime" at the bottom.
12. Select either "Electronic Chime" if you are using an Electronic door chime or "Mechanical Chime" if you are using a Mechanical door chime.
Then select OK.
13. You will see a "Saved." message when the settings are successfully saved.
Mobile: DMSS
Home to locate your device list.
Select your DB11 device and tap on ... icon.
9. Tap on Device Details.
10. Tap on Ring Linkage
11. Under Link Chime, Tap on the + button to add the Door Chime.
12. Select either Electronic Chime if you are using an Electronic door chime or Mechanical Chime if you are using a Mechanical door chime.
Then tap on Save on the bottom.
13. Tap on Save again to complete the setup.
8. Open the iDMSS Plus or gDMSS Plus app on your mobile device.
Go to the "Home" screen and select "Device" at the bottom.
Select your DB11 from the list of devices
9. From the DB11 Device Settings screen select "Ring Linkage"
10. Select "New Linkage"
11. Select "Associate Third-party Chime" at the bottom
12. Select either "Electronic Chime" if you are using an Electronic door chime or "Mechanical Chime" if you are using a Mechanical door chime.
Then select "OK"
13. You will see a "Saved." message when the settings are successfully saved
