Testdb6

Revision as of 22:59, 10 March 2022 by Andy (talk | contribs)

DB6 Physical Install And Connect to DMSS

Description

This article will cover how to physically connect a DB11 to a door chime and how to connect it to the mobile app, DMSS.

Prerequisites

DMSS on IOS

Video Instructions

Step by Step Instructions

IMPORTANT NOTICE: Disable the power to your doorbell and door chime before beginning physical installation

1. If not already done, disconnect the wire from the existing doorbell, that goes between it and the "FRONT" terminal on the door chime (#1 below).
Disconnect the wire from the exisiting doorbell, that goes between it and the Power Transformer (#2 below)

DB11PhysicalInstall0.png

2. Flip over the DB11 and connect the Wire Harness wires, included in the box, to the back of DB11

DB11PhysicalInstall1.png

3. From the DB11 and the door chime, twist the two wires, one from the end of the Wire Harness and one from the door chime, and connect them together with a Wire Nut or Clip (included in the box).
Repeat this for the other set of wires from the DB11 and the Power Transformer.

DB11PhysicalInstall2.png

4. The door chime that is already installed will either be Electronic or Mechanical.

DB11PhysicalInstall3.png

Make sure the two wires are already connected to the FRONT and TRANS connections. If they are not, adjust them so they are.

DB11PhysicalInstall4.png

5. If you are using a Mechanical door chime skip to Step 7. If you are using an Electronic door chrime continue from here.

With the Electronic door chime, you will need to add the Chime Kit (included in the box)

DB11PhysicalInstall5.png

6. Connect the wire set shown below (included in the box) to the Chime Kit with the green Terminal Block (also included in the box).
Connect the wire set in line with the DB11, door chime, and AC Power Transformer in the configuration shown in the diagram below:

DB11PhysicalInstall6.png

7. The DB11 will now be installed in place of your previous doorbell.
It is safe to turn the power back on to the door bell system/power transformer

DB11PhysicalInstall7.png

8. Open your mobile app and you MUST follow instruction below to complete your Door Chime Setup.

Note: There are two mobile apps that available to support this product series.

IDMSS Icon.pngMobile: iDMSS Plus & gDMSS Plus

Go to the Home screen and select Device at the bottom.


Select your DB11 from the list of devices.

DB11PhysicalInstall8.png

9. From the DB11 Device Settings screen select "Ring Linkage".

DB11PhysicalInstall9.png

10. Select "New Linkage".

DB11PhysicalInstall10.png

11. Select "Associate Third-party Chime" at the bottom.

DB11PhysicalInstall11.png

12. Select either "Electronic Chime" if you are using an Electronic door chime or "Mechanical Chime" if you are using a Mechanical door chime.
Then select OK.

DB11PhysicalInstall12.png

13. You will see a "Saved." message when the settings are successfully saved.

DB11PhysicalInstall13.png

DMSS New Icon.pngMobile: DMSS

Tap on DMSS Icon Live Home.png Home to locate your device list.

Select your DB11 device and tap on ... icon.

DMSS Share Device 2.jpg

9. Tap on Device Details.

DMSS Share Device 2-1.jpg

10. Tap on Ring Linkage

DMSS Ring Linkage Setup 10.png

11. Under Link Chime, Tap on the + button to add the Door Chime.

DMSS Ring Linkage Setup 11.png

12. Select either Electronic Chime if you are using an Electronic door chime or Mechanical Chime if you are using a Mechanical door chime.
Then tap on Save on the bottom.

DMSS Ring Linkage Setup 12.png

13. Tap on Save again to complete the setup.

DMSS Ring Linkage Setup 13.png