-
Relay out
4 KB (640 words) - 19:46, 15 August 2016
-
After enabled, relay activation will work. Check it and enable the PIR alarm.
Relay out
4 KB (598 words) - 19:32, 15 August 2019
-
Relay-out
Check to enable relay-out alarm.
2 KB (254 words) - 22:36, 12 May 2016
-
Controller 12V power output. It is to control the on-off alarm relay output. It can be used to control the device alarm output. At the same time
Controller 12V power output. It is to control the on-off alarm relay output. It can be used to control the device alarm output. At the same time
65 KB (9,813 words) - 19:16, 1 July 2016
-
===Alarm relay specifications===
3 KB (450 words) - 00:22, 16 November 2017
-
# Support alarm activation setup: record, relay-out, send email and snapshot.
464 bytes (67 words) - 19:48, 18 March 2016
-
1. NVR/HCVR/DVR with Alarm IN relay functionality
3 KB (464 words) - 19:47, 2 August 2019
-
| valign="top" bgcolor="#ffffff" width="126"|Relay Output
8 KB (1,028 words) - 20:45, 3 August 2023
-
| valign="top" bgcolor="#ffffff" width="130"|Relay Output
7 KB (910 words) - 22:16, 3 August 2023
-
* NVR/HCVR/DVR with Alarm IN and OUT relay functionality
[[Category:Relay]]
5 KB (799 words) - 20:30, 1 August 2019
-
...: IP-based video systems, Video & audio streaming, Pan-tilt-zoom control & relay output and Video configuration & multicast.
14 KB (2,125 words) - 21:40, 15 November 2021
-
==How to Connect a Relay Module==
''' Please check all of your systems (IPC, Relay Module, and Alarm Output Device's) power requirements and specifications be
3 KB (529 words) - 21:34, 25 July 2016
-
...push wire to the push circuit and back to ground (GND). The LED (or unlock relay) is connected via the green NO wire and then back to the yellow GND wire.
3 KB (559 words) - 23:29, 15 June 2016
-
...e will wire a simple LED that is powered off of the 12v supply. The unlock relay here is wired supplying power through the 12v terminal to the NC or NO term
3 KB (494 words) - 17:19, 15 June 2016
-
a. Relay operated outputs: This alarm output operation is used on a majority of Dahu
*~0 ohm circuit once the relay is activated.
2 KB (291 words) - 20:15, 22 June 2016
-
...n_Delivery/Integrating_Video_Intercom_with_Acccess_Control|Integrating VTO relay to 4-Door Access Controller]]<br />
17 KB (2,648 words) - 14:05, 15 April 2024
-
| class="xl65"|One (1) Relay Out for Main Lock
6 KB (813 words) - 21:28, 2 October 2018
-
* Unlock - This will trigger the relay output on the VTO (typically wired to a door)
5 KB (886 words) - 20:05, 20 November 2019
-
The VTO2111D-WP features a relay (NO/NC/COM) that can be activated when using the unlock door option. Please
937 bytes (146 words) - 21:54, 20 November 2017
-
...ck any other options you may want such as Record & Record Delay, Snapshot, Relay out (1, 2, or both)alarm Delay and email.
2 KB (333 words) - 23:10, 28 February 2019
