3rd Party VMS/Control4

Revision as of 21:16, 23 April 2019 by JP (talk | contribs) (NVR Setup)

Control4

Overview

Using this driver allows a Control4 dealer to add an icon in the watch menu. This will enable the Control4 System to use the Monitor-Out/HDMI/VGA connector to integrate Dahua devices.

Control4 infograph.png

Instructions

Prerequisites

Driver Features

  • Allows NVR Icon on Watch Menu, and Connection paths for HDMI and VGA into a Control4 video system
  • Event Connection for Triggers FROM NVR (using either, connection binding or Composer Event)
  • NUMBER buttons select that channel (example: Button 6 = Camera 6 on the TV)
  • Setup RED, GREEN, YELLOW, and BLUE buttons to trigger different views on TV
  • Uses Control4’s cable Proxy
  • Connection paths for camera proxy interface

Driver List

Dahua Firmware to Enable Control4 Integration

XVR Firmware

Model Firmware
  • X72A2A
  • X51A3E
  • X52A3A
  • X52A3N
  • X51A1E
  • X51A2E
  • X72A3A
  • X54A5L
  • X58A5S

NVR Firmware

Model Firmware
  • DHI-NVR52A08-8P-4KS2
  • DHI-NVR52A16-16P-4KS2
  • DHI-NVR54A16-16P-4KS2
  • DHI-NVR58A16-16P-4KS2
  • DHI-NVR58A32-4KS2
  • N52A4P
  • N54A4P
  • N52B2P
  • N52B3P
  • N52B5P
  • N54B3P
  • N42B1P
  • N42B2P
  • N42B3P

IP Camera Firmware

Model Firmware
  • N52BF3Z
  • N52BM3Z
  • N51BD22
  • N51BD23
  • N51BL22
  • N51BL23
  • N51BI22
  • N51BI23
  • N41BD22
  • N41BK22
  • N41BD12-W
  • N41BL12-W
  • N45BB5Z
  • N45CB5Z
  • N25BL5Z
  • N25CL5Z
  • N45BL5Z
  • N45CL5Z
  • N25BL5Z
  • N25CL5Z
  • N45BA5
  • N25BA5
  • N85CM5Z
  • N85CL5Z
  • N85CB5Z
  • N65CB5Z
  • N65CL5Z
  • N45CL5Z-B
  • N24BL52
  • N24CL52
  • N24BL53
  • N24CL53
  • N24BL56
  • N24CL56
  • N84BG44
  • N84CG54
  • N44BG52
  • N44CG52
  • N44BG53
  • N44CG53
  • N44BG56
  • N24BG52
  • N24CG52
  • N24BG53
  • N24CG53
  • N24BG56
  • N44BN52
  • N44BN53
  • N44BN56
  • N24BN52
  • N24BN53
  • N24BN56
  • N44BE53
  • N24BE53
  • N84CL52
  • N84CG52
  • N64CB32
  • N64CB33
  • N64CL52
  • N64CL53
  • N64CG52
  • N64CG53
  • N44BB33-B
  • N44BL52-B
  • N44CG52-B
  • N55BS5
  • DH-IPC-HFW4239TN-ASE
  • DH-IPC-HDBW4239RN-ASE

Setup NVR Streams (H.264, MJPEG)

Note: Certain older Control4 equipment require MJPEG for video stream (HC800, HC250, Infinity Touchscreens etc..). If these older devices are used at property, the dealer MUST enable Sub Stream and set to MJPEG. If dealer is using T3 and EA controllers, MJPEG does not need to be used

  • Log into NVR or use GUI and go to Setup
  • Select IMAGE, ENCODE
  • Choose Proper Channel (repeat for each channel)
  • Change Main Stream Settings to the following (note: these settings are best practices; individual systems may require modification of these settings for certain applications)

1. Code-Stream Type: Continuous

2. Compression: H.264

3. Resolution: 1280*720(720P)

4. Frame Rate(FPS): 13

5. Bit Rate Type: VBR

6. Bit Rate: 1024

IF MJPEG is required do the following:

1. Enable Sub Stream on Channel

2. Compression: MJPEG

3. Resolution: 704*480(D1)

4. Frame Rate(FPS): 13

5. Bit Rate: 1024

Camera Viewing Setup

  • Search for Dahua in Search of ComposerPro
  • Add PTZ and Fixed cameras for all cameras you want to view in Control4

Control4 Setup2.png

  • Make connection for each camera to the correct channel on the nvr

Control4 Setup3.png

  • By default, the driver chooses the video stream from the NVR. This is acceptable for 1 to 2 cameras only. If more cameras are required, Select Driver Actions: Set Video from Camera directly, then enter the camera ip address, username and password.

Control4 Setup4.png

Setup Event Notification (Trigger C4 FROM NVR)

1. Log into NVR or use GUI and go to Setup

2. Select Network, Alarm Center

3. Enable Alarm Center

4. Protocol Type: ALARM CENTER

5. Host IP: IP Address of Director

6. Port: Port listed on Driver Property: Server Communication Port

7. Self-report Time: Never

Control4 Setup5.png

8. Select Event (choose which event you want to monitor)

9. Choose which event you want Control4 to be notified of

10. Create proper event action. The event action should be Alarm Upload

11. In Composer, Select: Alarm Upload Event and add actions associated with event

Control4 Setup6.png

NOTE: Currently there is only a single notification that can come from the NVR.