-
5. On the IP Camera, go to Setup->Network->WiFi
2 KB (239 words) - 16:39, 11 October 2016
-
5 KB (724 words) - 18:27, 12 July 2019
-
==Setup Zero Channel==
'''How to setup Zero Channel on Dahua NVR'''
971 bytes (137 words) - 23:07, 2 November 2020
-
==How to Setup RAID==
*''Enterprise Rated HDD is highly recommended for RAID Setup.''
1 KB (173 words) - 12:28, 16 July 2021
-
===Step by Step Instructions to Setup RAID5===
2. Go to Setup->Storage->RAID Info
698 bytes (102 words) - 19:40, 2 August 2019
-
==How to setup Hotspare==
* Completed the instructions to setup RAID [[RAIDSetup|Link Here]]
1 KB (169 words) - 19:43, 2 August 2019
-
...s displayed something similar to the above image after completing the RAID Setup, that is normal. Your RAID is working properly.
332 bytes (44 words) - 22:56, 13 July 2016
-
=Recorder Alarm Setup=
This article is to show you instruction of how to wire and setup the alarm input from the recorder.
3 KB (464 words) - 19:47, 2 August 2019
-
3 KB (468 words) - 15:00, 16 October 2019
-
Follow the step by step instructions and video instructions below to setup P2P via Easy4IP on the Mobile Application.
1 KB (227 words) - 00:33, 17 August 2016
-
156 bytes (22 words) - 22:34, 12 May 2016
-
==FTP Setup Core FTP Server==
2. Click, "Setup"
2 KB (308 words) - 15:25, 3 June 2016
-
==How to Setup Multicast==
3 KB (443 words) - 23:22, 2 November 2020
-
==How to Setup Alarm Recording Using A Physical Alarm==
4. Login to the NVR, and click, "Setup"
2 KB (276 words) - 16:39, 11 August 2016
-
==How to Setup NKB1000 over Network==
===Step by Step Setup Instructions===
3 KB (477 words) - 22:50, 19 January 2024
-
==How to Setup NKB1000 via USB and SmartPSS==
2 KB (326 words) - 22:58, 12 May 2016
-
==How to Setup NKB1000 via RS485==
*Please select protocol according to the speed dome type. The default setup is DH-SD
3 KB (533 words) - 19:11, 4 November 2020
-
1 KB (193 words) - 21:10, 25 July 2016
-
2. Select setup.
...rectly and trigger appropriately. Now check PTZ Activation and then select setup.
1 KB (176 words) - 22:11, 5 July 2017
-
==How to Setup Date and Time==
...t the '''Skip''' button in the lower right corner, until you reach '''Time Setup'''.
2 KB (319 words) - 00:25, 25 July 2017
-
* Check the camera setup. Please make sure It supports the products of other manufacturers.
498 bytes (84 words) - 17:02, 19 April 2016
-
|Brightness is 0. Please restore factory default setup.
|Video quality setup is too low.
10 KB (1,564 words) - 20:39, 7 December 2022
-
# Log into the web interface of the camera. Click on Setup, General and then the date and time option.
666 bytes (99 words) - 22:31, 12 May 2016
-
# Use Web Service of the NVR. Under the setup tab > image > remote device.
837 bytes (130 words) - 22:07, 12 May 2016
-
!colspan="2"| IP Camera 5.0 UI Setup
!colspan="2"| IP Camera Initial Setup
5 KB (767 words) - 18:28, 21 November 2023
-
[[Category:Setup]]
431 bytes (66 words) - 22:10, 1 August 2019
-
Main Menu->Setup->Storage->Destination->Local
[[Category:Setup]]
540 bytes (72 words) - 22:15, 6 August 2019
-
5. After logging in, go to Setup->System->General->Date&Time
599 bytes (97 words) - 19:26, 23 June 2023
-
The Security Code will be sent to the email that was setup during device initialization, the email will be shown partially below the Q
1,019 bytes (172 words) - 21:32, 23 June 2023
-
===How to Setup Remote Access for IP Camera===
Note: This setup is only for IP cameras that are not connected to the same LAN as the NVR or
1 KB (240 words) - 21:41, 26 June 2023
-
* Section 1: Encode setup bar
Video setup
5 KB (733 words) - 22:57, 11 August 2016
-
..., zoom, focus, iris, preset, tour, pan, scan, pattern, aux on, off and PTZ setup button. See Figure 3-1.
4. Complete scan path setup.
3 KB (402 words) - 22:55, 30 June 2016
-
Before the setup, please make sure you have installed the auto iris.
It is to set device default setup.
9 KB (1,540 words) - 18:07, 12 December 2017
-
* You can click on setup button to set location information. You can use the mouse to drag location
2 KB (277 words) - 00:05, 29 June 2016
-
Note: Some series don’t support ROI setup function. [[file:IPCROI.jpg|600px]]
700 bytes (88 words) - 23:20, 11 August 2016
-
Please click the Save button to save current setup.
836 bytes (122 words) - 23:20, 11 August 2016
-
===Audio Setup===
The setup here is for audio encode mode and the bidirectional talk encode both.
2 KB (257 words) - 22:43, 11 August 2016
-
...vice needs to reboot to activate the new setup once you modify the default setup.
'''Step 5''': You can see the setup is OK if you can see there are output information such as “Reply from 192
3 KB (431 words) - 23:17, 11 August 2016
-
...function. Please save current setup and then reboot the device to get the setup activated.
658 bytes (111 words) - 22:49, 11 August 2016
-
...the connection is OK or not .Before the email test, please save the email setup information.
2 KB (285 words) - 22:29, 13 July 2016
